===== Walkera Master CP - 3D Settings =====

Buildem336 (Manuel) 3D settings

Here is a video of the stock Master CP flying with the settings below. He is not using the deviation firmware but I converted the settings over for the deviation firmware.

Walkera Master cp 3d flight

http://youtu.be/izTsmE6Ibyo
  * TX Power=100mW  * Channels=7  * Protocol=DEVO  * No Fixed ID  * Throttle Hold is active on RUDD D/R switch.  * Stick Mode 2
If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.
  * Travel Adjustment: Pitch = 54%  * Pitch Travel has been set so that there is no bogging of the motor.  * 7 Point Throttle and Pitch Curves.
Model 9 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S.

Model 9-2 has Zero Degree Pitch when throttle hold is on.

This will help minimize damage in a crash as the swash and blades will be at mid stick zero degrees pitch.

This will also help prevent a boom strike.

The swash does not move when TH is on.

If you want control of the swash in TH to help you land in a crash don’t use this model use Model 9 instead.

Model 2 is for deviation firmware v3 and the Devo 8/8S/12.

Model 28 is for deviation firmware v3 and the Devo 10.

See the post below this for the Devo 6S Model.

I have test flown this model in the Devo 10 transmitter.

__Fixed ID__

My model does not use a Fixed ID.

If you used a Fixed ID with the original Walkera firmware you must clear the Fixed ID in the Receiver with the Bind Plug.

If you don't clear the Fixed ID the model will not bind.

If you want to use a Fixed ID you can enter the same Fixed ID you had for the original Walkera firmware.

Example: Your original Walkera firmware Fixed ID was: 123456

Assign the Deviation Fixed ID: 123456

You can also assign any Fixed ID that you want to use. You don't have to use the original Walkera firmware Fixed ID. Clear the Fixed ID in the Receiver with the Bind Plug then assign any Fixed ID that you want to use.

__Throttle Curve__

Normal: -100, -33, 33, 100, 100, 100, 100

ST-1: V Shaped Throttle Curve

ST-2: 100% Flat Across

Throttle Hold is active on RUDD D/R switch

__Pitch Curve__

Normal: About -1.5* negative pitch. Zero degrees pitch at mid stick.

ST-1: Full +/- 3D pitch curve. Zero degrees pitch at mid stick.

ST-2: Full +/- 3D pitch curve. Zero degrees pitch at mid stick.

__Gyro Gain__

64% for Normal and Stunt modes. This value is equal to the Walkera firmware value of 82% gyro gain.

__DR/EXPO__

Switch Position

0- ELEV D/R = 100% EXP LIN

0- AILE D/R = 100% EXP LIN

RUDD D/R = 100% EXP EXP -6%

Switch Position

1- ELEV D/R = 100% EXP LIN

1- AILE D/R = 100% EXP LIN

RUDD D/R = 100% EXP EXP -6%

Download the Configuration Settings File.

Right click the "model.ini " and select "Save Target As" or "Save Link As" depending if you are using IE or Firefox.

Install the configuration settings file into your models folder.

This will over-right the current file so make sure that model slot doesn’t

have a model being used in it. If it does rename the configuration settings file

to another number that you have free.

Example: The file you downloaded is named model5 so change the “5? to another slot

number that you don’t have a model setup for. If you have model slot 6 open rename the file to model6

See my video:

How to Import/Export Deviation Firmware Models

http://youtu.be/aXkvtbCXzsk

-

[[ .:walkera_master_cp_-_3d_settings:model9-2_2014-01-26 ]] 

[[ .:walkera_master_cp_-_3d_settings:model2 ]] 

[[ .:walkera_master_cp_-_3d_settings:model28 ]] 

[[ .:walkera_master_cp_-_3d_settings:model9 ]]