DeviationWiki model_config

2-channel racing yacht config

Anonymous (anonymous@undisclosed.example.com) — 2015-05-02T02:13:35-0700

2-channel racing yacht config RC racing yachts have a very simple, and fairly standard, configuration. Many competition classes - both national and international - are restricted to 2 functions, which translates two two controllable devices, or two channels.

4G6S (2610S) Pitch Servo Jump

Anonymous (anonymous@undisclosed.example.com) — 2013-03-05T20:20:15-0700

4G6S (2610S) Pitch Servo Jump I just downloaded this software to my Devo 8s and I must say it is nice to be able to control all of my helicopters from this controller. I downloaded the 4G6 profile a few pages back and had to change a few settings and I was able to come up with a working solution, but I experience a large servo jump on the pitch servo near center. I haven't been able to find a solution so I tried a nightly build from sunday to see if it would correct the issue, which it would no…

250 280 QAV Quadcopter devo 7E 3 way switches

Anonymous (anonymous@undisclosed.example.com) — 2016-01-10T00:56:47-0700

250 280 QAV Quadcopter devo 7E 3 way switches Just put this one together only tested indoors needs a bit of trimming as quad is drifting might need sub trim quad is QAV 280 with orange ppm receiver dsmx F3 pro Racing controller 2×3 way switches working, using clean flight.(Running Radio Firmware nightly builds) deviation-devo7e-v4.0.1-583c468.zip

Align T-Rex 150 DFC - 3 Difficulty Modes

Anonymous (anonymous@undisclosed.example.com) — 2014-04-30T19:03:11-0700

Align T-Rex 150 DFC - 3 Difficulty Modes I made this model based off my other Align T-Rex 150 DFC models. It has 3 difficulty modes: Beginner, Standard, 3D. The difficulty modes are controlled with the Flight Mode Switch. Normal - Beginner Settings

Align T-Rex 150 DFC - 3D Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-10T09:07:20-0700

Align T-Rex 150 DFC - 3D Settings This model is for use with the Spektrum DSM2/DSMX Satellite Receiver. * 7 Point Throttle and Pitch Curves * Throttle hold on the RUDD D/R switch * TX Power=100mW * Channels=7 * Protocol=DSMX * No Fixed ID * Stick Mode 2

Align T-Rex 150 DFC - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-10T09:03:40-0700

Align T-Rex 150 DFC - Beginner Settings This model is for use with the Spektrum DSM2/DSMX Satellite Receiver. * No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast. Dont fly outside in wind in normal mode. You wont be able to pull the heli down if the wind takes the heli.

Align T-Rex 150 DFC - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-10T09:06:00-0700

Align T-Rex 150 DFC - Standard Settings This model is for use with the Spektrum DSM2/DSMX Satellite Receiver. * 7 Point Throttle and Pitch Curves * Throttle hold on the RUDD D/R switch * TX Power=100mW * Channels=7 * Protocol=DSMX * No Fixed ID * Stick Mode 2

Align T-Rex 150 DFC - Ultra Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-31T08:23:51-0700

Align T-Rex 150 DFC - Ultra Beginner Settings This model is different than my Beginner Settings model posted on this web site. It is even tamer and will hover at about 1 line above the half stick throttle mark. I made this model for the beginner who is flying a CP helicopter for the first time. This model is made just to hover and fly around.

Align Trex 250 DFC 3GX using DSM2

Anonymous (anonymous@undisclosed.example.com) — 2013-05-03T07:57:56-0700

Align Trex 250 DFC 3GX using DSM2 This is my model.ini for a Align 250DFC with 3GX and DSM2 Orange satellites. I've not flown it much as I have found out my ESC is weak but it can hover. 3GX is mounted as per the manual, plugs forward, upside down in the belly behind the rudder servo.

APM - arducopter multirotor spektrum dsm2 8ch rx

Anonymous (anonymous@undisclosed.example.com) — 2015-05-25T08:25:55-0700

APM - arducopter multirotor spektrum dsm2 8ch rx Channel 5 FLIGHT MODE 1 - FMODE0 FLIGHT MODE 2 - FMODE1 FLIGHT MODE 3 - FMODE2 FLIGHT MODE 4 - GEAR1 FLIGHT MODE 5 - MIX1 FLIGHT MODE 6 -MIX2 Throttle Hold style switch(handy for helicopter guy like me) - the quad goes in stabilize and 0 throttle

AR.Drone 2.0

Anonymous (anonymous@undisclosed.example.com) — 2014-01-21T04:23:38-0700

AR.Drone 2.0 I have for my AR.Drone2.0 Rc Kit “mirumod” in operation. My configuration (Devo 6S) Model Type = Plane TX Power = 150mW Channels = 7 Protocol = DSM2 Hard id = 123456 Stick Mode 2 Gear 0 = landing Gear 1 = Start Everything still without flips!

Bixler 2: 2 position flaps and 3 flight modes ;)

Anonymous (anonymous@undisclosed.example.com) — 2013-08-21T16:33:26-0700

Bixler 2: 2 position flaps and 3 flight modes ;) Hi all! I've just bought the Devo 10 and installed the 3.0 version of deViation. I'm learning minute after minute new functions of the software. It's extremely powerful. I don't know how the programmers could have thought to something so complex and so advanced if I'm burning my brain to understand it!

Bixler 2 with Flaps + Devo 8s + RX802

Anonymous (anonymous@undisclosed.example.com) — 2014-02-08T08:50:51-0700

Bixler 2 with Flaps + Devo 8s + RX802 H-King Bixler 2 with Flaps configured with 50% and 100% on MIX1/MIX2. Devo8s + RX802 Flaps servos connected to GEAR and AUX1 bixler2_2014_02_09

Blade 130

Anonymous (anonymous@undisclosed.example.com) — 2012-10-14T08:22:22-0700

Blade 130 Switches: ELEVATOR DR = EXPO/DR for Aileron and Elevator FMODE0 = indoor FMODE1 = 3D (outdoor) RUDDER DR = throttle hold cheers Graziano model3

Blade 130 X - 3D Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-26T09:06:30-0700

Blade 130 X - 3D Settings * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DSMX * No Fixed ID * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Blade 130 X - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-09T05:17:18-0700

Blade 130 X - Beginner Settings * Re-posted 1/9/2014 - Accidentally deleted the other post while updating it. * No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast. Dont fly outside in wind in normal mode. You wont be able to pull the heli down if the wind takes the heli.

Blade 130 X - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-17T09:34:08-0700

Blade 130 X - Standard Settings UPDATE: 5/13/13 I have updated all the models which have the same name as before. * Notice of Ch 3 being 0 not -100 has been corrected. * DSM2 has been changed to DSMX. * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DSMX * No Fixed ID * Stick Mode 2

Blade 130x bo105 wobble

Anonymous (anonymous@undisclosed.example.com) — 2016-02-15T05:23:36-0700

Blade 130x bo105 wobble Hello, I'm new to this forum and also a bit of a noob with the deviation software. This week i got my new devo 10 and i upgraded it with deviation. My solo pro, mini cp and 4f200lm all work fine with the software and the model configs i downloaded of this forum but my red bull 130x is having a cyclical wobble when i fly it. When hovering it isn't falling out of the air but the servi is acting as if its compensating for heavy wind while flying inside. I downloaded almost…

Blade 180 QX HD

Anonymous (anonymous@undisclosed.example.com) — 2014-01-27T16:49:25-0700

Blade 180 QX HD This model was made by kreidler. I added DR/EXPO functions and added my custom GUI which also includes Battery and TxPower to the b/w screens. Model 37 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S. * This model will not work for deviation firmware v2.1 or v3.

Blade 180CFX with Devo8S

Anonymous (anonymous@undisclosed.example.com) — 2014-10-30T14:00:00-0700

Blade 180CFX with Devo8S My setup for the new Blade 180-CFX model3 ciao, Bernd

Blade 200 SRX Devo 10 with tamed down flight modes

Anonymous (anonymous@undisclosed.example.com) — 2016-04-10T11:47:53-0700

Blade 200 SRX Devo 10 with tamed down flight modes Guys, I have been working on several triple flight mode ini file for the Devo 10 for all my helis. For the 200 SRX this is basically three scaled mixes within each of the blades flight modes. Aim is to tame the thing right down so guys can fly and learn without drilling it into the deck and can with a flick of a switch up the flight model and at the third level are pretty well at the blade defaults.

Blade 200QX

Anonymous (anonymous@undisclosed.example.com) — 2014-05-27T02:19:01-0700

Blade 200QX Here's a .ini for the Blade 200QX little device from Horizon Hobby. I've stolen Tom Z's .ini for 350QX ( found here ), which is derived from Fabien's. I've modified safety value to -150. It works flawlessly on my Devo 8S. FMod for modes selection, Aile D/R for rates, Rudd D/R for starting & stopping motors.

Blade 200qx 3 way switches devo7E

Anonymous (anonymous@undisclosed.example.com) — 2016-01-09T22:08:02-0700

Blade 200qx 3 way switches devo7E File for blade 200qx Devo7E (3 way switches) throttle cut left spring switch flight modes left 3way switch easy at top, medium in middle, hard at bottom of switch range, no timers set, some channels may have to be reversed not throttle due to mine being put in a different frame. please Test and report any issues.

Blade 230s

Anonymous (anonymous@undisclosed.example.com) — 2015-08-30T13:41:55-0700

Blade 230s Model file for the blade 230s, setup according to the manual. model1

Blade 300x with AR7200BX BeastX

Anonymous (anonymous@undisclosed.example.com) — 2012-11-28T03:49:20-0700

Blade 300x with AR7200BX BeastX This is my first try at the AR7200bx. It works, but all I have done is low test hovers so far. (partly due to weather) Always check for reversed controls! I don't have stock servos so you may need to reverse something.

Blade 350 QX from Horizon

Anonymous (anonymous@undisclosed.example.com) — 2013-09-15T07:10:29-0700

Blade 350 QX from Horizon Hi all, I think a lot of you have already heard about the Blade 350 QX which should be soon available. Im not sure to take one, but in the doubt I decide to make a model config for my radio based on the manual ( here ). Here is the information I found:

blade 350 qx RTH problem with devo 7 e

Anonymous (anonymous@undisclosed.example.com) — 2014-03-15T10:33:43-0700

blade 350 qx RTH problem with devo 7 e hi i have a problem with my blade 350, when i flying goes in return to home mode, and a little seconds later changes in the normal mode, smart or stability mode is the same.... i have the devo 7e with the 2 switch mods, and the actually nightly build

Blade 350QX Config/Template and Icon

Anonymous (anonymous@undisclosed.example.com) — 2014-11-10T14:17:42-0700

Blade 350QX Config/Template and Icon Hello everyone, Just recently picked up a Devo12s and uploaded Deviation firmware, so far my only RC is a Blade 350 QX Quad. I made this config/layout to utilize the blade basically as it is originally supposed to be configured.

Blade CX2

Anonymous (anonymous@undisclosed.example.com) — 2013-02-10T11:51:34-0700

Blade CX2 This updates my previous posted E-flight Blade CX2 model done on a Devo 10. After doing some flying on the previous posted model I found it was not getting the full range of motion out of the servos and corrected it. The rest remains the same.

Blade FP Helicopter - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-13T17:08:34-0700

Blade FP Helicopter - Beginner Settings This model will work on the following helicopters. * Blade SR 120 * Blade mSR/mSR-X * Blade mCX/mCX2 * Low dual rates and positive expo to tame the heli down. * Throttle hold on the RUDD D/R switch. * TX Power=100mW * Protocol=DSMX * No Fixed ID * Stick Mode 2

Blade FP Helicopters - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-13T17:10:19-0700

Blade FP Helicopters - Standard Settings This model will work on the following helicopters. * Blade SR 120 * Blade mSR/mSR-X * Blade mCX/mCX2 * Throttle hold on the RUDD D/R switch * TX Power=100mW * Protocol=DSMX * No Fixed ID * Stick Mode 2

Blade Inductrix for Devo 7E

Anonymous (anonymous@undisclosed.example.com) — 2015-09-19T02:20:58-0700

Blade Inductrix for Devo 7E Here is my config for the Blade Inductrix on Devo 7E, which is (heavily) based on Daryoon's Nano QX config. HOLD switches acro mode and FMOD changes rate between high and low rate (60%). The perfect quad for learning acro !

Blade mCP X

Anonymous (anonymous@undisclosed.example.com) — 2012-09-16T03:16:25-0700

Blade mCP X Very basic template for a stock mCP X. Includes Flight mode switch functional, and throttle cut via the GEAR switch. It's also pretty soft around the center of the sticks. No dual rates or gyro settings (mCP X has non-adjustable gyros anyway). This will more than likely require some adjustment depending on how well your swash is centered and all that. Should get ya started thought. Enjoy!

Blade mCPX - Ultra Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-02-01T17:33:47-0700

Blade mCPX - Ultra Beginner Settings This model is different than my Beginner Settings model posted on this web site. It is even tamer and will hover at about 1 line above the half stick throttle mark. I made this model for the beginner who is flying a CP helicopter for the first time. This model is made just to hover and fly around.

Blade mCPX V1/V2/BL- Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-15T08:07:04-0700

Blade mCPX V1/V2/BL- Standard Settings UPDATE: 5/13/13 I have updated all the models which have the same name as before. * Notice of Ch 3 being 0 not -100 has been corrected. * DSM2 has been changed to DSMX. This model is for the Blade mCPX V1/V2 and mCPX BL.

Blade mCPX V1/V2/BL - 3D Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-26T08:37:43-0700

Blade mCPX V1/V2/BL - 3D Settings This model is for the Blade mCPX V1/V2 and mCPX BL. * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DSMX * No Fixed ID * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Blade mCPX V1/V2/ BL - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-13T16:55:26-0700

Blade mCPX V1/V2/ BL - Beginner Settings UPDATE: 5/13/13 I have updated all the models which have the same name as before. * Notice of Ch 3 being 0 not -100 has been corrected. * DSM2 has been changed to DSMX. This model is for the Blade mCPX V1/V2 and mCPX BL.

Blade mQX

Anonymous (anonymous@undisclosed.example.com) — 2014-01-08T17:13:38-0700

Blade mQX * Throttle hold on the RUDD D/R switch * TX Power=100mW * Protocol=DSMX * No Fixed ID * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings. Model 19 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S.

Blade mSRX config for Devo8 V4.0

Anonymous (anonymous@undisclosed.example.com) — 2014-01-02T06:26:07-0700

Blade mSRX config for Devo8 V4.0 Blade mSRX mode for Devo8s, with a sticky throttle on channel 1 blademsrxmodel11

Blade Nano CP / NCPx

Anonymous (anonymous@undisclosed.example.com) — 2012-10-05T17:22:46-0700

Blade Nano CP / NCPx Attached is a config for the blade NCPx / Blade Nano CP. DR/Expo for ELE, AIL, RUD with corresponding switches on the TX. Throttle hold with Gear switch. FMODE0 gives you normal flight mode: pitch mostly positive and 5 points throttle from -100 to +100

Blade Nano CP S

Anonymous (anonymous@undisclosed.example.com) — 2015-10-17T03:31:29-0700

Blade Nano CP S Here my Devo8 S file for the new Blade Nano CP S Flight modes on FMOD 0-2 Motor Cut on RDD D/R Panic Button function on ELEV D/R Mix 0-2 Dualrate 100/80/70 model11-2-3

Blade NANO CP S DEVO 10 With SAFE

Anonymous (anonymous@undisclosed.example.com) — 2015-12-20T17:21:12-0700

Blade NANO CP S DEVO 10 With SAFE Ok, I worked it out. Took all day due to the fact I have trouble with Throttle[channel1] vs Collective[channel6] distinguishing between the two. I had to change the Devo 8 [gui-320×240] to Devo 10 [gui-128×64]. Switches all lined up, but I did change switch assignments.

Blade Nano CP X - 3D Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-26T08:53:43-0700

Blade Nano CP X - 3D Settings * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DSMX * No Fixed ID * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Blade Nano CP X - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-16T15:57:35-0700

Blade Nano CP X - Beginner Settings UPDATE: 5/13/13 I have updated all the models which have the same name as before. * Notice of Ch 3 being 0 not -100 has been corrected. * DSM2 has been changed to DSMX. * No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast.

Blade Nano CP X - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-16T16:21:12-0700

Blade Nano CP X - Standard Settings UPDATE: 5/13/13 I have updated all the models which have the same name as before. * Notice of Ch 3 being 0 not -100 has been corrected. * DSM2 has been changed to DSMX. * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DSMX * No Fixed ID * Stick Mode 2

Blade Nano CPX/mCPX/130X - 3 Difficulty Modes

Anonymous (anonymous@undisclosed.example.com) — 2014-04-30T21:33:53-0700

Blade Nano CPX/mCPX/130X - 3 Difficulty Modes I made this model based off my other Blade models. It has 3 difficulty modes: Beginner, Standard, 3D. The difficulty modes are controlled with the Flight Mode Switch. This model is for the Blade Nano CPX/mCPX BL.

Blade Nano QX

Anonymous (anonymous@undisclosed.example.com) — 2014-01-20T13:49:23-0700

Blade Nano QX This model was made by fabien for the Devo 8 with Deviation v3.0 I converted the v3 model to v4 and added my custom GUI layout which will work on all these transmitters: DEVO 6/6S/8/8S/10/12/12S. * This model will work on the Devo 7e but due to there is one less flight mode on that model you will not have all three flight modes FMOD0 - FMOD1 - FMOD2.

Blade NanoCPX/130X - Ultra Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-02-01T17:36:41-0700

Blade NanoCPX/130X - Ultra Beginner Settings This model is different than my Beginner Settings model posted on this web site. It is even tamer and will hover at about 1 line above the half stick throttle mark. I made this model for the beginner who is flying a CP helicopter for the first time. This model is made just to hover and fly around.

Blade/Walkera/Align - Standard Mixer

Anonymous (anonymous@undisclosed.example.com) — 2014-02-17T11:35:45-0700

Blade/Walkera/Align - Standard Mixer I just made some models from scratch using the Standard Mixer. One model is for the Devo 7e only. The other model is for the following transmitters: DEVO 6/6S/8/8S/10/12/12S The Blade CP models I recommend you adjust the Throttle Curves, Pitch Curves, DR/EXPO, and Pitch Travel (only for some models) according to what model Blade CP helicopter you have.

CB100

Anonymous (anonymous@undisclosed.example.com) — 2012-09-09T21:42:44-0700

CB100 Indoor setting, not that the CB100 would be capable to fly outdoors... ;) cb100

Config for Walkera Genius CP V2 Standard Mixer

Anonymous (anonymous@undisclosed.example.com) — 2014-11-03T22:24:53-0700

Config for Walkera Genius CP V2 Standard Mixer Hello, i want to show you my first try to translate the standard settings given in the Genius CP V2 Manual. Throttle Switch ist Motor off. This works for my Genius CP V2. May be its useful for some people.

Convert this module for a devo7e

Anonymous (anonymous@undisclosed.example.com) — 2015-05-02T04:26:04-0700

Convert this module for a devo7e Hi I found this module in the forum can it be changed to be used in a devo7e. It says it was for a devo 10. Thanks Gary cx2_model2

Delta Ray by HobbyZone with SAFE Technology

Anonymous (anonymous@undisclosed.example.com) — 2013-12-19T12:32:06-0700

Delta Ray by HobbyZone with SAFE Technology Settings for Hobbyzone Delta Ray: - Model Type: Airplane - Protocol: DSM2 - # Channels: 7 - Throttle, Aileron, Elevator, Rudder on channels 1 to 4 - Channel 5: Flight Modes for Beginner, Intermediate, Experienced on FMODE 1, 2, 3 respective.

DEVO 7e for FlightSim Sky-Gambler Storm-Raiders

Anonymous (anonymous@undisclosed.example.com) — 2015-02-01T08:27:14-0700

DEVO 7e for FlightSim Sky-Gambler Storm-Raiders Hi, this is the configuration I use for the Sky-Gambler Storm-Raider Flight Sim. It is a cheap and easy to use game. But lot's of fun. [img size=550] As you can see, I use the extra-swichtes on the TX. Look for

Devo 10 Fatshark Head tracking

Anonymous (anonymous@undisclosed.example.com) — 2014-02-28T07:38:39-0700

Devo 10 Fatshark Head tracking I spent a few days pulling out my hair trying to get my Devo 10 to play nice with a fatshark attitude. So I'm going to attach my last config file. This got all three axis on the fatshark working. Thank you model5_2014-02-28

Devo 10 for FX071 with 6G / 3G and 3 flight modes

Anonymous (anonymous@undisclosed.example.com) — 2016-03-18T16:05:32-0700

Devo 10 for FX071 with 6G / 3G and 3 flight modes okay here it is the official kiwi-craig FX 071 Devo 10 flight model Version 1 this has three flight modes, three tail modes, 6g AND 3G ! decent icons loaded against the toggle switches and a 5 point throttle curve, and a custom screen icon.

Devo 10 on Phoenix

Anonymous (anonymous@undisclosed.example.com) — 2013-07-21T19:29:36-0700

Devo 10 on Phoenix I've created a config for the Devo 10 when using the Phoenix flight sim. It's not really aimed at making the sim as realistic as possible, but more at squeezing as much functionality out of the sim/Devo combo as possible. I decided it made a good illustration of exactly how flexible this software is.

devo 12s with mini cp brushless

Anonymous (anonymous@undisclosed.example.com) — 2014-10-21T13:21:55-0700

devo 12s with mini cp brushless my config mini cp brushless +lipo 520.telemetrie,chronos,fmode 1 & 2 ,trims pitch and giro and more. model1_2014-10-21

DJI F550 / DEVO10 / Naza-M Lite

Anonymous (anonymous@undisclosed.example.com) — 2014-03-02T00:46:01-0700

DJI F550 / DEVO10 / Naza-M Lite Here is a config file for DJI F550 Hexacopter. Configuration: DJI F550 / Devo10 with FW 4.0.1 / Naza-M Lite + GPS. I think it will run with Naza-M V2 as well. Supports all flight modes and fail-save/comming-home. Also switchable scales for ELEV/AILE.

DJI Naza + GPS with R710 or R910 RX on DBUS output

Anonymous (anonymous@undisclosed.example.com) — 2013-08-23T03:09:56-0700

DJI Naza + GPS with R710 or R910 RX on DBUS output Attached is my profile (Devo 10), don't forget you'll still have to calibrate sticks and other channels in the assistant before you can use it! That's better to do it with a blank profile, don't worry if aileron & elevator channels are swapped, that's normal (weird channels order on DBUS), calibrate like that, it is fixed in my profile.

DJI Phantom

Anonymous (anonymous@undisclosed.example.com) — 2013-06-12T23:36:09-0700

DJI Phantom Hello, I have modified my DJI Phantom. First I Removed the stock RX module, and replaced it with the RX1202 I got with my Devo 12S. I Then added the WK-CTL01-D telemetry module. The included 4 temp sensors, I wrapped 1 under each motor. Ran the voltage sensor to the main flight pack. Also added the WK-GPS module. All fit nicely under the lid without any trouble.

DJI Phantom - Just a little help needed

Anonymous (anonymous@undisclosed.example.com) — 2014-04-19T09:18:29-0700

DJI Phantom - Just a little help needed First off. AWESOME work on this firmware. I love it. I have attached my config. I have it working great but I can't figure out the last 2 tweaks I need to make. 1. Throttle to -100 kills the motors. This makes me nervous lol. I would like to disable this. Maybe set the

Dromida Ominus Model for the Devo7e

Anonymous (anonymous@undisclosed.example.com) — 2015-01-26T10:52:12-0700

Dromida Ominus Model for the Devo7e Hi guys, this is a modelfile for the Dromida Ominus Quad. Credits go to Voyn and Tom Z the file is based on their work. on the Hold Switch - Throttle Hold on the FMOD Switch - Gyro is set on -30 on the 0 and 30 on the 1 Pos

E-Flite UMX HABU S DF180 Config DEVO10

Anonymous (anonymous@undisclosed.example.com) — 2015-08-16T16:25:52-0700

E-Flite UMX HABU S DF180 Config DEVO10 It took me a while to set this one up. Ch5 / Gear is Flight Mode and Ch6 is Panic Mode. I have this for a DEVO 10 and I use ELEV D/R for Sticky Throttle Hold. I use RUDD D/R for Panic mode. FMOD switch for Flight Modes of course. I have added Aileron to Rudder mixing with AUX4 knob as a Aileron to Rudder mix Gain. If the AUX4 is -100, then there is no Rudder mixed with the Ailerons. If the AUX4 is at +100, then there is maximum Rudder mixed with Ai…

Eachine Racer 250/general purpose 6ch RX+CF/BF/OP

Anonymous (anonymous@undisclosed.example.com) — 2015-12-03T14:02:56-0700

Eachine Racer 250/general purpose 6ch RX+CF/BF/OP All files use 6 channels (DSMX protocoll, change it according to your RX) Edit: forgot to mention they are for Devo 7e. model8 is for Openpilot: Channel 5 uses FMOD and HOLD to switch output between

Elevon mix help please

Anonymous (anonymous@undisclosed.example.com) — 2013-01-12T13:33:34-0700

Elevon mix help please I have tried, I just cant get my head around it. I have been using er9x on the old turnigy 9x for a while now and thought I could grip deviation quite easy. I have been through the manual, through the v-tail mix & elevon setup on that post here, but I just cant get it right. That elevon ini file gave me the ele/ail sticks wrong way around - my trying to fix it screwed it up. Below is my current model setup I thought should work, elevator seems to work and stick movement t…

F450 + Multiwii Mega AIO

Anonymous (anonymous@undisclosed.example.com) — 2014-04-22T11:59:20-0700

F450 + Multiwii Mega AIO Hi all, It's my first post & first contrib to the forum. :lol: I've a DJI F450 frame powered by Multiwii mega all in one. The receiver is an RX802 & Transmitter DEVO 8S For my personnal use, I've drew some icons for better use.

"fancy" BLADE MSR config

Anonymous (anonymous@undisclosed.example.com) — 2013-01-18T22:25:01-0700

"fancy" BLADE MSR config Hi! Please find attached my first attempt at a deviation config! Throttle hold is on rud D/R (normal at 0, -100 at 1)... so you can turn on your TX with all your switches @0 :cheer: FMOD has different rates for AIL & ELE & RUD (0 is 60,1 is 80 and 2 is 100%)

Feewing A-10 with Flight Stabilizer Devo 10

Anonymous (anonymous@undisclosed.example.com) — 2015-03-31T18:44:35-0700

Feewing A-10 with Flight Stabilizer Devo 10 Attached file is for my Feewing A-10 Model for DEVO 10 - It has Elevator, Rudder + Mixed Nose Gear for smaller turning radius + RT TRIM for separate nose gear trim than Rudder trim, Ailerons, “Slow” Flaps, gear, FMOD0,1&2 for an A3Super flight stabilizer + Aux4 Pot to tune Flight Stabilizer Gain in flight. Aileron, rudder and elevator all with duel rate + expo. I don't have Throttle hold yet. I might set it to Rudd DR1 later.

File for RCL Extreme One X

Anonymous (anonymous@undisclosed.example.com) — 2014-08-05T06:23:38-0700

File for RCL Extreme One X Here is a config file for RC Logger Extreme One X, PPM, DSM2. Configuration: model5 / Devo8s with FW 4.0.1 / Tested & running on my Walkera 8s. Supports all flight modes, 2nd 3-way SW for Acrobatic-Normal-Alt Hold, & 2 Pos SW.

Flip FPV Quadcopter

Anonymous (anonymous@undisclosed.example.com) — 2014-02-17T22:15:42-0700

Flip FPV Quadcopter This model was made by Rambosmurf which sent me the model. I converted it to the V4 firmware and added my custom GUI. Edit: 2-18-2014 The model has been updated. The new model name is Model1_FlipFPV_V2 The Quad is running the Crius AIOP V2 Board with GPS and MegapiratesNG software.

Flitetest F-22 Raptor Delta wing

Anonymous (anonymous@undisclosed.example.com) — 2014-08-20T16:26:03-0700

Flitetest F-22 Raptor Delta wing I spent some time looking for a ini file for the flitetest ft-22 raptor. I'm posting this in the hopes that it helps someone else. model6

Floureon H101 Devo10 Inverted flight Trainer

Anonymous (anonymous@undisclosed.example.com) — 2016-01-31T14:15:50-0700

Floureon H101 Devo10 Inverted flight Trainer Hi Guys, here is a Model.ini for The H101 - but this one is a bit special. I did this for using this quad (and maybe others in this style as well) as a 3D trainer, for train the inverted flight views. While flipping it to inverted mode, the Quad negates its Controls by itself - not good for beeing a trainer.

fy326 q7 quadcopter

Anonymous (anonymous@undisclosed.example.com) — 2015-05-04T19:20:33-0700

fy326 q7 quadcopter Devo 7e modded with(A7105 and nRF24L01 ) working with fy326 q7 quadcopter. I forgot I use the nightly build 05/03/2015. You will have to recalibrate you TX after the binding is done. I hope this help. model2

Genius CP

Anonymous (anonymous@undisclosed.example.com) — 2012-09-09T20:27:06-0700

Genius CP Genius cp with the brushless main motor mod. current file is set the stick mode 4 which i fly on so you need to select your stick mode if you use a different stick mode. performs really well but you might prefer to tweak a few settings..

Genius WK2801Pro mode

Anonymous (anonymous@undisclosed.example.com) — 2012-10-24T13:52:35-0700

Genius WK2801Pro mode Here it is WK Genius model2

Gyro Settings (Super CP)

Anonymous (anonymous@undisclosed.example.com) — 2013-03-09T07:58:47-0700

Gyro Settings (Super CP) So my Devo 10 and Super CP arrived yesterday. I only got to give the Super CP a quick hover test, as the only open space in the house with nothing fragile was about 6ft square :P . I then flashed Deviation to my transmitter and set about configuring the mixers for the Super CP. It took a little while to get used to but I'm getting the hang of it now. This firmware is great, you can make any channel do just about anything you could want.

HCP100S + DSMX satellite

Anonymous (anonymous@undisclosed.example.com) — 2015-01-21T13:18:01-0700

HCP100S + DSMX satellite Hi! Here's a config file for HCP100S with DSMX satellite. It is setup per the HCP100S Manual (throttle and pitch curves). Throttle Hold is !FMOD0, Normal mode is RUDD D/R 0 and Idle up id RUDD D/R 1 to mimic HiSKY Tx way with TH on the right and Idle switch on the left.

Heli-Max 100cp using Standard GUI

Anonymous (anonymous@undisclosed.example.com) — 2014-02-03T12:32:40-0700

Heli-Max 100cp using Standard GUI Hi all, Here's my 1st contribution to model files. It's for my Heli-Max 100 cp. I use this with my Devo 7e and a single 3 positon flight mode switch. this uses the Standard GUI and has a very soft Flight Mode 0.

Help converting my SuperCP to Phoenix Model - FMOD

Anonymous (anonymous@undisclosed.example.com) — 2015-01-17T14:28:32-0700

Help converting my SuperCP to Phoenix Model - FMOD Hi, I took my SuperCP model which is working fine and simply changed the transmitter protocol to PPM and changed the model name. This is working in Phoenix, except my FMod switches do not work as expected.

Help me stop Yaw output unless throttle is up

Anonymous (anonymous@undisclosed.example.com) — 2015-04-17T07:22:23-0700

Help me stop Yaw output unless throttle is up Hey guy's, I posted in this section cause I need help with my config, tho it does work pretty well. Feel free to download and use it as-is (or mod to suit) I set this up for the DSMX RX in my multiwii tricopters (I have 3 now) and on the 3D printed one's it's not an issue cause they have nice little legs keeping the small 6

Hisky FBL-70 On Devo 10 / HT8

Anonymous (anonymous@undisclosed.example.com) — 2013-07-29T20:36:28-0700

Hisky FBL-70 On Devo 10 / HT8 This is my Hisky FBL-70 fixed pitch configuration for the Devo 10 w/HT8 module. I started with the 4ch w/Dual-Rates template but made a lot of changes. This flys well for me but as always - test all functions before attempting to fly and use at your own risk.

Hisky FBL-80cp On Devo 10 / HT8

Anonymous (anonymous@undisclosed.example.com) — 2013-08-01T16:49:01-0700

Hisky FBL-80cp On Devo 10 / HT8 This is my Hisky FBL-80cp configuration for the Devo 10 w/HT8 module. I started with the 6ch Helicopter template but made a lot of changes. Flight modes are based on my skill level. Transition between modes is smooth.

HiSky HCP100S with nRF soldered

Anonymous (anonymous@undisclosed.example.com) — 2014-12-21T07:25:32-0700

HiSky HCP100S with nRF soldered FMODE 0/1/2 = Throttle LOW/MEDIUM/HIGH (always the same pitch curve, no normal mode) RUDD DR0 Throttle HOLD AILE DR1 reset timer For Devo10 model16_2014-12-22

HM830 Paper Airplane Model.ini

Anonymous (anonymous@undisclosed.example.com) — 2014-05-04T09:17:42-0700

HM830 Paper Airplane Model.ini Here is an initial model for the HM830 Paper Airplane. While it is a 2-channel airplane, I've built the protocol with the following channels: Ch1 (Throttle Stick): Throttle Ch2 (Aieron Stick): Rudder Ch3: Accelerate (I believe this just sets max throttle)

Hobby King Assault Reaper 500 with Devo12 config

Anonymous (anonymous@undisclosed.example.com) — 2016-03-06T04:55:54-0700

Hobby King Assault Reaper 500 with Devo12 config Here are initial Settings for the Hobby King Assault Reaper 500 (like Stingray 500). The Settings are like the settings from the manual with small improvements: - If you switch the flight mode the Reaper will not jump or fall.

HobbyKing Turnigy Stadium Track 1/18 RC Car

Anonymous (anonymous@undisclosed.example.com) — 2014-02-05T09:48:59-0700

HobbyKing Turnigy Stadium Track 1/18 RC Car [img size=320](1).jpg[/img] I use this model.ini in my Devo 10. I use mode 2 and I set everything on right stick. With MIX0-1-2 you increase the steering 60/75/100. With STUNT0-1-2 you increase the throttle: 40/70/100.

HobbyZone Champ

Anonymous (anonymous@undisclosed.example.com) — 2012-12-01T20:25:10-0700

HobbyZone Champ The HobbyZone Champ is a 3 channel lightweight tail dragger, flying weight of 1.3 oz (39g) comes with a transmitter using only 4 AA batteries. I have experienced in-flight control drop outs maybe using the Devo 10 will help. Since I want to use the Devo 10 for my entire airborne fleet, plus the power output options with Deviation this was an obvious path.

How to Program Snap-Flap Aileron on Devo10 ???

Anonymous (anonymous@undisclosed.example.com) — 2015-11-04T06:30:32-0700

How to Program Snap-Flap Aileron on Devo10 ??? Hello, when i fly my Glieder on windy Days, it´s very hard to Land, because the Wind gets lot off Lift up to the Modell. To stop the Lift, i want to put the Aileron´s in an Spoiler Poition (Snap-Flap), to get drag (but must be also steered like Ailerons)

Hubsan H107D+ Devo 7E ini

Anonymous (anonymous@undisclosed.example.com) — 2016-01-11T15:26:47-0700

Hubsan H107D+ Devo 7E ini here is my ini file for the devo 7e for the h107D plus headless is on hold switch. flip on fmod switch. video record on up button snapshot is on down button model2-2-3-4

Hubsan X4

Anonymous (anonymous@undisclosed.example.com) — 2012-11-26T12:56:09-0700

Hubsan X4 For DEVO 8S - requires compatible Flysky module fitted () Protocol=Hubsan4 Number channels=4 Tx power=30mW 3 flight modes: FMode D/R Expo (Indoors) 0 - AILE 60% 20% 0 - ELEV 60% 20% 0 - RUDD 60% 0% (Outdoors) 1 - AILE 80% 10%

Hubsan X4 config

Anonymous (anonymous@undisclosed.example.com) — 2012-12-31T04:54:10-0700

Hubsan X4 config Hello my X4 config : 2 mode - 70% dualrate (rudder 60%), 25% expo --> green icon - 100% dual rate, 0% expo (3D) --< yellow icon throllte cut : RUD DR --> red icon 2 chrono throttle command for model icon : i choise second icon rename x4.bmp

Huiying X6058 Model File

Anonymous (anonymous@undisclosed.example.com) — 2015-07-21T18:16:21-0700

Huiying X6058 Model File Attached below is a model file for a Huiying X6058 quadcopter, that will likely work with other Huiying models. It is a modification of one I received from Frequent Flyer (youtube.com), when I had trouble getting my mod of a CX10 file to work as expected. He may have some trouble recognizing it, but it is the starting point.

issues with nano qx 3d model file

Anonymous (anonymous@undisclosed.example.com) — 2015-08-03T15:51:31-0700

issues with nano qx 3d model file hey there I'm trying to set up my nano qx 3d on my devo 8s, but I'm having trouble getting it to work properly. I currently am using the fmode switch to change between the different flight modes but instead of having 3 settings its acting like it only has 2. also I set the gear switch to be the flip switch but it does not work at all for me. anyone have any thoughts?

JJRC1000 questions

Anonymous (anonymous@undisclosed.example.com) — 2015-05-14T20:11:52-0700

JJRC1000 questions I'm a noob with ini files. Below is a bit of the .ini for my JJRC1000. Channel 5 makes the LEDs turn on or off. If I remove all the lines for channel 5 from my ini file (and give it no information about channel 5) then once bound the quad's default behavior is for the LEDs to slowly blink on and off. So therefore: the quad has three settings for its lights: on, off, and blink.

JJRC 1000A Quadcopter (V202)

Anonymous (anonymous@undisclosed.example.com) — 2014-09-13T06:45:36-0700

JJRC 1000A Quadcopter (V202) Hi, see below for a JJRC 1000A model file. The model name will be “JJIRC POLY”, you can change to your particular needs. This is using the “Hubsan X4 for 7e 10” icon located at: http://www.deviationtx.com/forum/bw-icons-for-devo-7e-10/1615-hubsan-x4-for-7e-10 Requires the NRF24L01 module:

JJRC H20 Hex Devo 7e

Anonymous (anonymous@undisclosed.example.com) — 2015-11-12T11:59:26-0700

JJRC H20 Hex Devo 7e Here is my model.ini for the JJRC H20 micro hexcopter. model9-jjrch20 Rates: SW B0/1/2 This model has three rates, 60%, 80% and 100%. Note that 100% is really quick and the yaw is incredibly fast. Flip mode: (Channel 6) FMODE 0/1 Headless mode (Channel 9) SW A2, while engaged lights blink three times repeating

Juncheng 3015-1 / 3015-2

Anonymous (anonymous@undisclosed.example.com) — 2015-10-09T06:42:37-0700

Juncheng 3015-1 / 3015-2 Thank Goebish that allowed me to best use these beautiful micro quadcopters, I am attaching my ini files for DEVO 7E configured to switch 3×2 Here's a test version for Devo 7e: www.dropbox.com/s/bj3ey2q0loy1t7k/deviat...

KDS450C (noFBL) with RX2801Pro

Anonymous (anonymous@undisclosed.example.com) — 2012-12-28T10:06:50-0700

KDS450C (noFBL) with RX2801Pro Here my .ini for KDS450C and Icon KDS450C TX-Mode: 2801Pro with full 3d mode Please check (after install) subtrimm! Throttle=zero--> RUDD D/R switch Gyro-Mode (AVCS/Normal)--> Gear switch model1

KK2.0 Multirotor

Anonymous (anonymous@undisclosed.example.com) — 2016-12-05T16:11:58-0700

KK2.0 Multirotor KK2.0 Multirotor with the Spektrum Receiver. KK2.0 Multirotor with the Devo Receiver. I am using the Spektrum AR6100 6 Channel Receiver 2.4 GHz, Protocol=DSM2. If you have a Spektrum Receiver with DSMX you might have to switch the Protocol=DSM2 to Protocol=DSMX

KK2 quadcopter settings for Deviation on Devo8s

Anonymous (anonymous@undisclosed.example.com) — 2013-03-02T14:53:15-0700

KK2 quadcopter settings for Deviation on Devo8s This is my setup for my KK2 quads, MODE 2. Allows me to have a range of usable modes using just one switch and recover faster when the quads gets out of hand, lining up for stunts and for a safer takeoff/landing by flicking to FMOD0.

Ladybird DSM2

Anonymous (anonymous@undisclosed.example.com) — 2012-11-08T09:33:33-0700

Ladybird DSM2 For Deviation 8S, protocol DSM2. Flight Modes and Throttle Hold (via the 'RUDD DR' switch). Mode change (Normal, 3D) with GEAR switch. FMode1 - indoor FMode2 - outdoor, more aggressive FMode3 - outdoor, most aggressive Trottle curves for hovering at about 50% throttle.

Lanyu ASW28

Anonymous (anonymous@undisclosed.example.com) — 2014-08-01T07:25:41-0700

Lanyu ASW28 This may be useful to someone. May also be good starting point for other gliders. Devo 8s Mode 2 ADIF Aileron differencial E>F Elevator > Flap mixing A>R Aileron > Rudder mix. R/DR sw F>A Flap > Aileron mix. AIL/DR sw F>E Flap > Elevator.

MasterCP and V120D02SV2 With Thanks to Tom Z

Anonymous (anonymous@undisclosed.example.com) — 2013-01-26T12:39:59-0700

MasterCP and V120D02SV2 With Thanks to Tom Z A special Thank you goes to Tom Z, because without his guides I would have given up. These are for: V120D02S for Devo. Pitch limits are dropped down to 56%. Expo/DR are 100/+10 and 100/Line. Rudder is at 100/-10 for faster responce. Gyros at 80%

Mcpx v2 Full IdleUp

Anonymous (anonymous@undisclosed.example.com) — 2012-10-24T13:53:51-0700

Mcpx v2 Full IdleUp And at last, my Mcpx config with idle-up and Throttle cut. model1

MINI CP standard config for ver.3.0

Anonymous (anonymous@undisclosed.example.com) — 2013-04-08T17:57:39-0700

MINI CP standard config for ver.3.0 Here is a Standard setup for Ver 3.0, Walkera Mini CP config with Custom Wallpaper and colors. Throttle hold,... Rud DR Flight Mode,......Normal, Stunt 1, Stunt 2 Air DR ,..........Ail,and Ele, DR Mix,.........

Model config for MSH Brain/Ikon/Tracx

Anonymous (anonymous@undisclosed.example.com) — 2014-12-15T08:36:20-0700

Model config for MSH Brain/Ikon/Tracx This is a working model file I use on my Protos 800 w/ MSH Brain. It is meant to show how you can set up bank switching and gov w/ throttle hold and separate throttle cut switch. It is Spektrum DSM* channel order.

MSR DEVO 10 Toggle Icons

Anonymous (anonymous@undisclosed.example.com) — 2013-03-27T06:14:43-0700

MSR DEVO 10 Toggle Icons Hi! I've attached a file that take advantage of the new-ish sexy toggle switch icons. IT defaults to high rates, but ELEV DR 1 will bring it to low rate mode Gear is TH Mix is DR for AIL/ELE FMOD is tail rate Ail DR stops the timer.

Multiwii Crius AIO Pro Devo7e with 3x2 switch mod

Anonymous (anonymous@undisclosed.example.com) — 2014-06-23T13:10:32-0700

Multiwii Crius AIO Pro Devo7e with 3x2 switch mod Set up for Spektrum DSM2 receivers (I use a LemonRX 8ch). Arm Switch has “OK” symbol for disarmed, exclamation mark for armed. (HOLD switch) GPS has arrow down symbol for Position Hold, house icon for RTH. (Left 3 position switch), third position is off and blank.

My Align T-Rex 450 + RX1002 + Devo 10 config file

Anonymous (anonymous@undisclosed.example.com) — 2013-08-25T01:47:54-0700

My Align T-Rex 450 + RX1002 + Devo 10 config file Hi, This is the config file I am using for my Airwolf, having a T-rex 450SE inside with a DEVO 10. It might not be the most professional config, but am flying this daily, so it works ;-) Enjoy. If you have some improvement ideas, please share B)

Ni Hui U207

Anonymous (anonymous@undisclosed.example.com) — 2015-05-01T19:30:07-0700

Ni Hui U207 Like my last thread start here, for the Syma X11, I see a need for standalone thread for the NiHui U207 quadcopter. It's a really good model. Thanks to SeByDocKy :) for telling us in detail how good that Quad really is. So I was very happy to see report(s) that the U207 SHOULD work on Deviation using the 717 protocol.

Nine Eagles B319 Black Hawk for Devo 6

Anonymous (anonymous@undisclosed.example.com) — 2015-04-24T09:43:10-0700

Nine Eagles B319 Black Hawk for Devo 6 As title says. model15

Nine Eagles Solo Pro 125 - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-02-04T15:28:30-0700

Nine Eagles Solo Pro 125 - Beginner Settings Nine Eagles Solo Pro 125 (125A) * No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast. Dont fly outside in wind in normal mode. You wont be able to pull the heli down if the wind takes the heli.

Nine Eagles Solo Pro 125 - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-02-04T15:29:56-0700

Nine Eagles Solo Pro 125 - Standard Settings Nine Eagles Solo Pro 125 (125A) * Low dual rates and positive expo to tame the heli down * Throttle hold on the RUDD D/R switch * 7 Point Throttle and Pitch Curves * TX Power=100mW * Channels=6 * Protocol=J6Pro * No Fixed ID * Stick Mode 2

Nine Eagles Solo Pro 180 3D - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-02-01T08:57:44-0700

Nine Eagles Solo Pro 180 3D - Beginner Settings Nine Eagles Solo Pro 180 3D (318A) This model was started by ave1 and I added the rest of the settings needed. ave1 test flew the model with good results. * No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast.

Nine Eagles Solo Pro 180 3D - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-02-01T08:59:42-0700

Nine Eagles Solo Pro 180 3D - Standard Settings Nine Eagles Solo Pro 180 3D (318A) This model was started by ave1 and I added the rest of the settings needed. ave1 test flew the model with good results. * Low dual rates and positive expo to tame the heli down * Throttle hold on the RUDD D/R switch * 7 Point Throttle and Pitch Curves * TX Power=100mW * Channels=7 * Protocol=J6Pro * No Fixed ID * Stick Mode 2

Nine Eagles Solo Pro 180 3G

Anonymous (anonymous@undisclosed.example.com) — 2013-01-19T14:27:57-0700

Nine Eagles Solo Pro 180 3G I made and tested configuration for NE Solo Pro 180 3G, based on the configuration for Walkera helicopters . Switch “GEAR” is used to control the fifth channel - the gyro sensitivity and has a value the same as in J6Pro: 25,75 points.

Nine Eagles Solo Pro 287 + Devo 7e

Anonymous (anonymous@undisclosed.example.com) — 2014-09-16T06:19:42-0700

Nine Eagles Solo Pro 287 + Devo 7e Normal = -5º,0º,10º FMODE1 = -10º,0,10º nesolopro287

Nova Quanum (eventually Cheerson CX-20)

Anonymous (anonymous@undisclosed.example.com) — 2014-08-11T11:21:00-0700

Nova Quanum (eventually Cheerson CX-20) Here is a model config pour the quad “NOVA Quanum”. It might work for the Cheerson CX-20 My Devo 7E is settled with 2 additional switches Left Side (SWA) is a 2-position Right side (SWB) is a 3-position

Orange R610 in TyphoonPro 450-Heli (DSM2)

Anonymous (anonymous@undisclosed.example.com) — 2012-09-30T05:02:27-0700

Orange R610 in TyphoonPro 450-Heli (DSM2) * RX: Orange R610 (DSM2, 6 channels) * swashplate in 120X-mode (elev servo in front, aile on the right, aux1 on the left) * FLIGHT MODE switch influences throttle (FM0: start, FM1: easy artistics, FM2: full power) and pitch * GEAR switch switches throttle off (displayed on screen) * elevator, aileron and rudder reduced to 60%, full way with corrsponding switches, shown on screen * gear output (ch5) is used for gyro sensitivity (switched by the MI…

Orange RX3S on a F9F Panther EDF Jet

Anonymous (anonymous@undisclosed.example.com) — 2014-09-24T23:09:47-0700

Orange RX3S on a F9F Panther EDF Jet Notes: RUD DR0 - safety throttle switch, value -110 ELE Complex Page 3 MIX THR -> ELE, 3 point curve, setup but not currently used. CH6 is Aux Ctrl Gyro -> Gear0 model10 [video]

Parkzone Ultra Micro T-28 Trojan

Anonymous (anonymous@undisclosed.example.com) — 2013-03-23T06:17:15-0700

Parkzone Ultra Micro T-28 Trojan At the request of someone here the .ini file for the UM T-28 Trojan. Settings: Protocol: DSMX THR trim all the way down (-110) GEAR1 - throttle cut, value -110 1. ELE 65%, 100%, EXPO 15% MIX THR -> ELE, 3 point 0-8-18 to prevent pitch up on full THR

Parkzone UMX Sbach 342

Anonymous (anonymous@undisclosed.example.com) — 2015-04-29T12:45:26-0700

Parkzone UMX Sbach 342 Hi ! Here's a model config for a Parkzone UMX Sbach 342 Stunt plane. It's meant for intermediate to advanced pilots. No expo, but FMODE 0 will scale inputs to 70% on Rudder and Elevator, 65% on Ailerons. Enjoy ! umxsbach342

Passer-X V-Tail Motor Glider DSMX Devo6

Anonymous (anonymous@undisclosed.example.com) — 2013-08-23T18:42:24-0700

Passer-X V-Tail Motor Glider DSMX Devo6 for Deviation 3.0.0 MIX 0 Motor stop MIX 1 Slow motor run MIX 2 Motor run D/R 0 Camber flap in THR Stick(link elevator) D/R 1 Flap & Spoiler in THR Stick(link elevator) Gear 1 Very soft Spoiler (lock out camber flap)

Turnigy Q-BOT micro

Anonymous (anonymous@undisclosed.example.com) — 2017-05-23T02:28:38-0700

Turnigy Q-BOT micro Looks like there's no settings for qbot micro. here's my file model7 Here is my configuration for the Q-Bot micro. I use a Devo 10 in Mode 2 with the 4in1 module. I have the switch RUDD D / R as a safety switch (throttle cut) and AUX4 for the sensitivity of the gyro (gyro gain).

QR Ladybird

Anonymous (anonymous@undisclosed.example.com) — 2012-09-09T21:39:49-0700

QR Ladybird This is a simple indoor version. It hasn't enough craft for flipping, just cruising. EDIT: I replaced the file, please try again... EDIT2: Since PB changet the DEVO code to use at least 8 channels, I had to move the gyro from channel 5 to 7, but at least I made it even simpler

Raquel Quadcopter and Devo10

Anonymous (anonymous@undisclosed.example.com) — 2014-02-01T09:37:31-0700

Raquel Quadcopter and Devo10 Here is my config using a Deltang Rx73 Receiver in PPM mode. FC is a MW32 (NAZE32 compatible) with Harakiri SG 2.5. The Devo 10 is running 4.0.1. model5

RealFlight Devo10

Anonymous (anonymous@undisclosed.example.com) — 2015-02-15T17:05:18-0700

RealFlight Devo10 This will allow you to access all the channels for use in the RealFlight Simulator and give you full access to map your channels as you see fit within RealFlight. Rud DR switch will activate 80(30%) travel(DR). realflight_2015-02-15

Reversing Pitch in the Model File

Anonymous (anonymous@undisclosed.example.com) — 2013-01-20T04:39:04-0700

Reversing Pitch in the Model File I using a Devo 10 with the current FW, RX802 and a BeastX. The Aile and Pit servos are operating in the opposite directions between cyclic and pitch control. In the BeastX I can swap the direction so that they are correct for cyclic or pitch but can't get them to operate in the correct direction for both. I'm still struggling a little with the mixing sources in the model file. Hexperience's

Robbe ARROW SR/EVO FP for Devo7E

Anonymous (anonymous@undisclosed.example.com) — 2014-04-06T03:35:04-0700

Robbe ARROW SR/EVO FP for Devo7E Hello, i am completly new to the CP Helis and bought an Devo 7e to get with this Open Source Software a Multiprocol Sender. I am created two Profiles for my own Robbe ARROW EVO and Robbe ARROW SR FP Helicopters. The Switch HOLD is for Stoping the Main Engine (fast stop) and FMOD is for agility.

Rules

Anonymous (anonymous@undisclosed.example.com) — 2012-09-09T14:55:16-0700

Rules Please post one model per thread. And make sure the post Subject clearly denotes the model. The description should ideally contain anything relevant to the config (is it aggressive or tuned for beginners; which protocol is it setup for; etc)

Skyartec WASP nano CP

Anonymous (anonymous@undisclosed.example.com) — 2013-04-02T23:20:18-0700

Skyartec WASP nano CP Set up my nanoCP on Devo 10, 1. Sport flying only, no 3D, pitch from -2 to +10 degrees 2. Dual Rate switch on AIL D/R , 80/100%, applied to AIL/ELE/RUD all 3. Gyro gain on Mix0/1/2 giving -60/-75/-90 waspnanocp

Solo Pro 125 Smooth Config

Anonymous (anonymous@undisclosed.example.com) — 2013-03-22T02:19:26-0700

Solo Pro 125 Smooth Config Hello All, this a beginner/slowed down,smooth config that makes my new Solo Pro 125 BNF really stable on my Devo8/Deviation 2.1.1 TX. Elev DR on Elev switch, Aileron DR on Ail Switch. Gyro Hi/Low on Gear switch. Trims set to +-20%.

Super CP

Anonymous (anonymous@undisclosed.example.com) — 2013-03-11T19:16:25-0700

Super CP Finished my config for the Super CP and said I'd share it in case it's useful to someone. I tried to keep it close to the standard setup in the heli's manual. Throttle hold is controlled by RUDD D/R, cuts throttle but does not affect pitch.

Super CP / Master CP - Devo 7e - V3.0 model

Anonymous (anonymous@undisclosed.example.com) — 2013-12-25T13:25:21-0700

Super CP / Master CP - Devo 7e - V3.0 model Herewith my Devo8 model for Walkera mini helis. It is a conversion from my Devo8s model which I fly with, converted and tested on the Devo7e emulator. Please use it as an example and not to fly your heli without testing.

Syma X1 model and icon

Anonymous (anonymous@undisclosed.example.com) — 2014-02-18T21:06:33-0700

Syma X1 model and icon Used a posting of a Hubsan X4 model as a starting point, and the icon is from a zip file someone posted here. Will add credits if I can find them again. Icon is for Devo7e/10. Fmode0: very gentle Fmode1: about the same as stock tx high rate

Syma X5C config for Video and Photo use

Anonymous (anonymous@undisclosed.example.com) — 2015-07-14T10:20:48-0700

Syma X5C config for Video and Photo use The X5C-1 model file below is a modification to a file posted here earlier by Durete; many thanks for an excellent starting point. It is tailored for Video/Photo using the camera on the X5C-1 and fits a Devo 7e with two switches. I use the late nightly builds. If you use the current release, you may have to change the model type to PLANE.

SYMA X5SC Explorer 2

Anonymous (anonymous@undisclosed.example.com) — 2016-01-20T23:12:25-0700

SYMA X5SC Explorer 2 Here is a .ini file i use for the SYMA X5SC Explorer 2 (that is what it says on the box anyway). I am nowhere near to beeing an expert in programming .ini files. I build it using 4 different files i found around in the forum (including one for JJRC H20). The combination of those files gave my quad all the abilities it should have. I share it for anyone who might want to try it too. I am using Nightly Builds and DEVO 10.

Syma X11 config

Anonymous (anonymous@undisclosed.example.com) — 2015-05-01T17:38:44-0700

Syma X11 config As some of us are now successfully controlling our X11 quads with Deviation modded Devo controllers using the SymaX protocol, I went looking for an official “model config” thread here. Sorry if one ALREADY exists, in which case this should go there. But I couldn't find one, so I'm starting one.

Syma X12 config.

Anonymous (anonymous@undisclosed.example.com) — 2015-05-06T14:36:32-0700

Syma X12 config. Starting a thread for this model, which uses the SymaX protocol, which is available (as of now) in the nightly builds (but not the 4.01 release). My config attempts to push the Yaw rate on this slow Yaw model. The X12 yaw doesn't benefit as much as the X11 model's yaw rate does to DeviationTX custom controls.

T-rex 450 FBL-RX701 Devo-ZYX-S FBL module...

Anonymous (anonymous@undisclosed.example.com) — 2012-10-01T11:23:14-0700

T-rex 450 FBL-RX701 Devo-ZYX-S FBL module... T rex 450 FBL(Tarot module) 3D flights setup,Gov. store mode on (YGE esc) Swashplate : none (ccpm in the FBL module) Elev.+Ail. Cyclic Dual Rate/EXPO : ELEV D/R switch(-10%,+15% Expo) Rudder Dual rate/EXPO : AIL D/R switch (

T-REX 450 Flybarless RX2702 V (2801 pro)

Anonymous (anonymous@undisclosed.example.com) — 2012-11-08T05:45:20-0700

T-REX 450 Flybarless RX2702 V (2801 pro) It's just a first tentative, can be improoved. Doesn't work with fixed id model9

T-Rex 450 SE V2 with RX601

Anonymous (anonymous@undisclosed.example.com) — 2012-11-10T08:50:25-0700

T-Rex 450 SE V2 with RX601 on request, my T-Rex 450 config hardware: ESC: Kotronic Jazz 40 LV (Governor Mode and Soft Start configured) Gyro: GY-401 Motor: Stock (3700KV) RX: RX601 rx channel assignment: ch1 (ele): rear swashplate servo ch2 (ail): right swashplate servo

tandem rotor in tx ccpm mixing

Anonymous (anonymous@undisclosed.example.com) — 2014-04-15T16:06:28-0700

tandem rotor in tx ccpm mixing So I've been hooked on the idea of a tandem rotor helicopter lately, but all mixing boards for this purpose are out of production as far as I can tell. This left me pondering doing the mixing in the tx using the many virtual channels Deviation tx provides.

Tarot/Align 450 DFC w/ Walkera 2702v 3-axis

Anonymous (anonymous@undisclosed.example.com) — 2012-10-03T14:46:55-0700

Tarot/Align 450 DFC w/ Walkera 2702v 3-axis Tarot 450 dfc: rx2702v-d 3-axis receiver. CC Ice 50 governed to 3100rpm with 9.3:1 gear ratio, 3400kv motor. You will need to set up different throttle curves if you are not using a governor. ds415m cyclic servos. savox sh-1257mg tail servo.

Tested Standard GUI V922 WL-T6 Devo 8s combo

Anonymous (anonymous@undisclosed.example.com) — 2013-10-10T04:56:53-0700

Tested Standard GUI V922 WL-T6 Devo 8s combo I have developed a Standard GUI model & icon for a WL V922 using a Devo 8s with a WL-T6 adapter. This should probably work for a HCP100 / FBL100 and HT8 as well but I have only tested it on the V922. This model is tuned for intermediate level 2D flying.

Trex450Pro FBL 2801 & Devo - BeastX/HobbyMate

Anonymous (anonymous@undisclosed.example.com) — 2013-01-26T12:36:08-0700

Trex450Pro FBL 2801 & Devo - BeastX/HobbyMate A special Thank you goes to Tom Z, because without his guides I would have given up. These are for: Trex 450 Pro FBL with Beastx/Hobbymate sytem, not sure about Tarot/CopterX but should be close. One file is for a 2801RX and the other for Devo's.

Trex 450 Pro Fbl Tarot XYZ

Anonymous (anonymous@undisclosed.example.com) — 2012-10-24T13:51:30-0700

Trex 450 Pro Fbl Tarot XYZ Hi, This is my ful config for my Trex 450 Pro Enjoy model3

Trex 500 FlyBar with 2801

Anonymous (anonymous@undisclosed.example.com) — 2013-01-27T15:32:20-0700

Trex 500 FlyBar with 2801 Attached is my set up for my Trex 500 Flybar, Logictec 2100 Gyro. Swash is at 55,55,60, Travel Adjustments 100%, Expo/DR at 100/20 on 1 for both Ele/Ail. 100/Line on 2. Rudder is 60/30 because gyro is very fast. Gyro at 30/-50 for to modes (your will probably be different)

Trim button as toggle mode for gyro gain

Anonymous (anonymous@undisclosed.example.com) — 2014-01-02T09:19:46-0700

Trim button as toggle mode for gyro gain Hi, I'm using my devo7e for mini cp, but since it doesn't have enough switches, I'm scratching my head to find alternatives for different functions/modes. I want to make my trim button to make my gyro gain toggle between 50 or 75

Tweak model.ini for RCL Xtreme

Anonymous (anonymous@undisclosed.example.com) — 2014-03-13T19:17:18-0700

Tweak model.ini for RCL Xtreme I am using the RC Loggers OneLink module piggybacked on my 7E (via training port) to fly the RCL Xtreme brushless quad. I followed the instructions for setting it up, and that went routinely. The setup includes a Learning routine where I start with a fresh blank airplane template and then operate each input in sequence, and learning happens. After that procedure, the model file is altered.

V120d02s

Anonymous (anonymous@undisclosed.example.com) — 2012-10-03T15:14:58-0700

V120d02s stock devo v120d02s v120d02s_2012-10-04

V500D01 DEVO

Anonymous (anonymous@undisclosed.example.com) — 2013-03-20T20:20:00-0700

V500D01 DEVO This is for the V500D01 with 2702v-D gyro RX. This is from a DEVO 12 You may need to edit the switches. (This is a good test to see how it translates to other TX's) Flight mode switch is for both throttle and pitch curves. F0 - Normal

v911 throttle curve question

Anonymous (anonymous@undisclosed.example.com) — 2015-02-25T06:37:06-0700

v911 throttle curve question Hey guys, I debated what sub-forum to put this question in and ended up here, dont know if it's best but dont really know what my question fits... I have been using (and modifying to taste) a v911 config file I found here, I'm very sorry but I do not recall who originally made / shared it to give credit to. Again I'm not at all claiming it's mine, all I've done is make some changes to fit my needs, the setup work initially goes to whoever it rightfully belongs to (…

V922 (FBL100) Is this normal?

Anonymous (anonymous@undisclosed.example.com) — 2014-05-11T12:03:07-0700

V922 (FBL100) Is this normal? Hi, I downloaded a FBL100 model file for my V922 and I've adjust it to suit my needs, i mean basic fly , no 3D, so I've a pitch curve with NO negative pitch and a max of 75% angle. The throttle curve goes from 0 to 100...

Vapor config

Anonymous (anonymous@undisclosed.example.com) — 2012-12-30T09:51:05-0700

Vapor config hello my config for parkzone vapor - 2 throtlle chrono - throttle cut (DR RUD) with red icon vapor

VL Toys VL959

Anonymous (anonymous@undisclosed.example.com) — 2013-02-18T04:44:03-0700

VL Toys VL959 Thottle hold = RUD D/R Dual Rate = FMOD vl_959

Walkera - QR Infra X - with + mode

Anonymous (anonymous@undisclosed.example.com) — 2013-01-21T09:58:51-0700

Walkera - QR Infra X - with + mode With this config you can fly Walkera - QR Infra X - in + mode. I need this for my Star Wars X-Wing Fighter. :) May also work with other quadro copter's. Test it with my Devo8S Walkera - QR Infra X - with + mode Star Wars X-Wing Fighter model29

Walkera 4#6S WK2401

Anonymous (anonymous@undisclosed.example.com) — 2012-12-03T00:05:03-0700

Walkera 4#6S WK2401 model.ini for 4#6S Protocole WK2401(4 channels) Txpower : 1mW (for indoor only) For beginner.(EXP/DR Scale : 50 , EXP : 30) Throttle cut on RuDD D/R Countdown on Throttle (4mn) model2

Walkera 4F200LM - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-22T18:44:10-0700

Walkera 4F200LM - Beginner Settings * No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast. Dont fly outside in wind in normal mode. You wont be able to pull the heli down if the wind takes the heli.

Walkera 4F200LM - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-22T18:45:52-0700

Walkera 4F200LM - Standard Settings * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DEVO * No Fixed ID * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Walkera CP Helicopters - 3 Difficulty Modes

Anonymous (anonymous@undisclosed.example.com) — 2014-04-30T17:15:59-0700

Walkera CP Helicopters - 3 Difficulty Modes I made this model based off my other Walkera CP Helicopter models. It has 3 difficulty modes: Beginner, Standard, 3D. The difficulty modes are controlled with the Flight Mode Switch. Normal - Beginner Settings

Walkera CP Helicopters - 3D Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-26T07:28:19-0700

Walkera CP Helicopters - 3D Settings This model will work on the following helicopters. * Walkera V120D02S * Walkera V120D02S V2 * Walkera Mini CP * Walkera Super CP * Walkera Genius CP V1/V2 * Walkera V100D08 *If you are using the V120D02S, V120D02S V2, Genius CP V1 with the WK-2801 Pro compatible Receiver change Protocol=DEVO to Protocol=WK2801.

Walkera CP Helicopters - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-06T15:12:20-0700

Walkera CP Helicopters - Beginner Settings [color=#ff0000]UPDATE:[/color] I corrected the switch icon issue that RandMental posted about below this post. The models have been updated and the switch icon assignments are now correct for the models that had the problem.

Walkera CP Helicopters - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-09T19:15:22-0700

Walkera CP Helicopters - Standard Settings This model will work on the following helicopters. * Walkera V120D02S * Walkera V120D02S V2 * Walkera Mini CP * Walkera Super CP * Walkera Genius CP V1/V2 * Walkera V100D08 *If you are using the V120D02S, V120D02S V2, Genius CP V1 with the WK-2801 Pro compatible Receiver change Protocol=DEVO to Protocol=WK2801.

Walkera CP Helicopters - Ultra Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-30T17:33:33-0700

Walkera CP Helicopters - Ultra Beginner Settings This model is different than my Beginner Settings model posted on this web site. It is even tamer and will hover at about 1 line above the half stick throttle mark. I made this model for the beginner who is flying a CP helicopter for the first time. This model is made just to hover and fly around.

Walkera FP Helicopters - Beginner settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-13T06:08:58-0700

Walkera FP Helicopters - Beginner settings This model will work on the following helicopters * Walkera Super FP * Walkera Genius FP * Walkera V200D01 w/Devo Receiver RX2437V-D * Walkera V200D02 w/Devo Receiver RX2440V-D * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Walkera FP Helicopters - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-06T18:50:14-0700

Walkera FP Helicopters - Standard Settings This model will work on the following helicopters * Walkera Super FP * Walkera Genius FP * Walkera V200D01 w/Devo Receiver RX2437V-D * Walkera V200D02 w/Devo Receiver RX2440V-D * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Walkera G400 GPS

Anonymous (anonymous@undisclosed.example.com) — 2014-01-28T17:44:33-0700

Walkera G400 GPS * GPS Functions on the Mix Switch. * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DEVO * No Fixed ID * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Walkera HM1#A stock...tame settings

Anonymous (anonymous@undisclosed.example.com) — 2012-09-09T20:51:53-0700

Walkera HM1#A stock...tame settings walkera hm1a rx 2608 .. protocal 2801 number of channels 8 stick mode 4 gyro sense set to mix switch with zero being HH the highest gyro... position 1 ten% lower and position 2 is set in rate mode Throttle Hold is set to Rudder D/R switch

Walkera Master CP - 3D Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-10T09:26:35-0700

Walkera Master CP - 3D Settings Buildem336 (Manuel) 3D settings Here is a video of the stock Master CP flying with the settings below. He is not using the deviation firmware but I converted the settings over for the deviation firmware. Walkera Master cp 3d flight

Walkera Master CP - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-06T18:23:48-0700

Walkera Master CP - Beginner Settings * No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast. Dont fly outside in wind in normal mode. You wont be able to pull the heli down if the wind takes the heli.

Walkera Master CP - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-06T18:25:11-0700

Walkera Master CP - Standard Settings * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DEVO * No Fixed ID * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Walkera Master CP Non - 3D Model (Devo 10)

Anonymous (anonymous@undisclosed.example.com) — 2013-03-24T08:42:46-0700

Walkera Master CP Non - 3D Model (Devo 10) Keep in mind I have kept this model to resemble the Walkera firmware. Mine is a Devo 10. There are no 3D settings here that will surprise you with a full throttle if you bump the FMOD switch by accident.

Walkera miniCP: beginner settings

Anonymous (anonymous@undisclosed.example.com) — 2012-10-12T17:08:36-0700

Walkera miniCP: beginner settings This beginner configuration is based on the 8k-template in the deviation user manual and on the beginner configuration by TomZ at rcgroups. - FMode 0: Throttle max. 80, pitch curve -11 to 78, indoors or no wind. - FMode 1: Throttle max. 86, pitch curve -35 to 87, outdoors

Walkera MiniCP for Devo7E

Anonymous (anonymous@undisclosed.example.com) — 2014-04-06T03:39:59-0700

Walkera MiniCP for Devo7E Hello, and the next one from me - my third Helicopter (the only CP i have) is a Walkera MiniCP so after upgrading to that OpenSource Software i need to setup this Helicopter. I found some Setups for Devo8 and Devo10 on this Forum, so i have played around with some Setups and generated from that three Setups for die MicoCP on the Devo7e

Walkera New V120D02s: beginner settings

Anonymous (anonymous@undisclosed.example.com) — 2012-10-12T17:13:11-0700

Walkera New V120D02s: beginner settings This beginner configuration is based on the 8k-template in the deviation user manual and on the beginner configuration by TomZ at rcgroups. - FMode 0: Throttle max. 62, pitch curve -8 to 56, no wind. - FMode 1: Throttle max. 75, pitch curve -22 to 65,

Walkera QR Ladybird

Anonymous (anonymous@undisclosed.example.com) — 2012-09-17T08:53:56-0700

Walkera QR Ladybird For Deviation 8S, protocol Devo. Flight Modes and Throttle Hold(via the 'RUDD DR' switch). FMode1 - indoor 2D (6-axis) FMode2 - outdoor, more aggressive 2D (6-axis) FMode3 - outdoor, 3D (3-axis) Trottle curves for hovering at about 50% throttle.

Walkera QR X350 Configs for Devo 10

Anonymous (anonymous@undisclosed.example.com) — 2014-01-02T10:38:03-0700

Walkera QR X350 Configs for Devo 10 I have finally taken the jump into Deviation with the new version 4 firmware. So far it is spectacular! I have created a couple of model configs for my QR X350 and wanted to share them here. QRX350-multi D/R Rudder, Elevator, Aileron Dual Rates all individually controlled via corresponding switch. All set at 60% when switch is set to 1, both full and dual rate mode use +60 exponential.

Walkera QR X350 Pro with Devo 10

Anonymous (anonymous@undisclosed.example.com) — 2014-07-20T12:24:22-0700

Walkera QR X350 Pro with Devo 10 Hello, since I haven't found a proper model config for my new X350 Pro, I made my own based on the channel values of the stock firmware Devo 10 which was shipped in the RTF paket of my X350 Pro. I found out the following values to be perfectly working with IOC and Position Hold/RTH:

Walkera Quads - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-08T16:52:33-0700

Walkera Quads - Beginner Settings This model will work on the following quads. * Walkera QR Ladybird V1/V2 * Walkera Hoten X * Walkera QR Infra X * Walkera QR Spacewalker * Walkera QR Scorpion * Walkera QR W100/100S * Walkera UFO MX400S * Walkera QR X400

Walkera Quads - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2013-04-09T20:11:44-0700

Walkera Quads - Standard Settings This model will work on the following quads. * Walkera QR Ladybird V1/V2 * Walkera Hoten X * Walkera QR Infra X * Walkera QR Spacewalker * Walkera QR Scorpion * Walkera QR W100/100S * Walkera UFO MX400S * Walkera QR X400

Walkera V100D01 - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-21T15:38:58-0700

Walkera V100D01 - Beginner Settings * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings. * Protocol=WK2401 * TX Power=100mW * No Fixed ID * Throttle Hold is active on RUDD D/R switch.

Walkera V100D01 - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-21T15:40:29-0700

Walkera V100D01 - Standard Settings * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings. * Protocol=WK2401 * TX Power=100mW * No Fixed ID * Throttle Hold is active on RUDD D/R switch.

Walkera V200D02

Anonymous (anonymous@undisclosed.example.com) — 2012-12-01T19:02:44-0700

Walkera V200D02 Walkera V200D02, what I have is actually a Banana Hobby Contra rebrand. This is my first contribution and I am just a newbie with these mixer settings, so everything is 'simple'. The DR/Expo and anything else were not changed from the default template.

Walkera V200D03 - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-12T19:57:06-0700

Walkera V200D03 - Beginner Settings * No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast. Dont fly outside in wind in normal mode. You wont be able to pull the heli down if the wind takes the heli.

Walkera V200D03 - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-12T19:58:23-0700

Walkera V200D03 - Standard Settings * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DEVO * No Fixed ID * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Walkera V450D01/D03 - 3D Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-07T18:11:37-0700

Walkera V450D01/D03 - 3D Settings * TX Power=100mW * Channels=7 * Protocol=DEVO * No Fixed ID * Throttle Hold is active on RUDD D/R switch. * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Walkera V450D01/D03 - Beginner Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-07T18:07:39-0700

Walkera V450D01/D03 - Beginner Settings * No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast. Dont fly outside in wind in normal mode. You wont be able to pull the heli down if the wind takes the heli.

Walkera V450D01/D03 - Standard Settings

Anonymous (anonymous@undisclosed.example.com) — 2014-01-07T18:09:50-0700

Walkera V450D01/D03 - Standard Settings * Throttle hold on the RUDD D/R switch. * 7 Point Throttle and Pitch Curves. * TX Power=100mW * Channels=7 * Protocol=DEVO * No Fixed ID * Stick Mode 2 If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Wing Wing Z-84 for Devo 7e (no switches) Elevons

Anonymous (anonymous@undisclosed.example.com) — 2014-05-28T07:37:36-0700

Wing Wing Z-84 for Devo 7e (no switches) Elevons Here is my base model for the full wing Z-84, 2 elevons aircraft, for a Devo 7e with range mod and no extra switches. The RUDDER stick is mapped as the AILERON, this way if you are used to give RUDDER to balance your plane like I do you won't panic. Also this way you have something like a

WL-Toys V913 Modelconfig

Anonymous (anonymous@undisclosed.example.com) — 2014-01-11T06:26:36-0700

WL-Toys V913 Modelconfig Attached my DEVO 7e Modelconfig. I adjusted after maximum servo travel. For more information watch at your Devo :-) model7

WL Toys - V911

Anonymous (anonymous@undisclosed.example.com) — 2012-09-12T17:53:33-0700

WL Toys - V911 Attached is a config file for the WL Toys V911 along with an icon for the model. Note that you need to complete the Flysky Hardware Mod in order to be able to use the Flysky protocol and bind to the V911. The document containing the details on how to complete the mod is available in the download section.

WL Toys V202 microquad - DEVO8S

Anonymous (anonymous@undisclosed.example.com) — 2013-06-02T17:06:36-0700

WL Toys V202 microquad - DEVO8S FMOD1 DR=80% EXP=0% for indoor. FMOD2 DR=94% EXP=0% for outdoor(can't filp) FMOD3 DR=100% EXP=0% for flip DR>=95% , it can flip,I set FMOD2 DR=94% you can get max. travel and it would NOT filp even you move stick to max. position!

WL Toys V911 with Devo 7E (Mode2)

Anonymous (anonymous@undisclosed.example.com) — 2016-02-01T12:31:51-0700

WL Toys V911 with Devo 7E (Mode2) Hi, here's a working (at least for me) config for the V911 and the Devo7E. Credits to: pfriedel in Devo 7e models rototophe in WL Toys - V911 A working V911.BMP vor Devo7E is inside this forum. Just search :) My setup is heavily inspired by the configs above. But i've made some modifications / changes, especially regaring the 7E (and some changes to the Reverse-Settings).

WL Toys V931 config for Devo10

Anonymous (anonymous@undisclosed.example.com) — 2016-04-13T03:07:23-0700

WL Toys V931 config for Devo10 Hi all, I've tried to find a model config for my devo10 and WLToys V931, but i never found what it... I've done it myself, and share with you ! Hope you enjoy ! model2

Wl toys V939

Anonymous (anonymous@undisclosed.example.com) — 2013-01-29T10:34:12-0700

Wl toys V939 Hello, here is my setup for the V939. to bind the V939 you have to do some hardeware modifications on the transmitter, described here: devo to flysky Expo & Dualrate on mix 0,1,2. works good for me and I hope for you too! model1

WLToys V686W for Devo 7e

Anonymous (anonymous@undisclosed.example.com) — 2016-02-29T23:34:29-0700

WLToys V686W for Devo 7e I've got this to work by modifying an existing file for the devo 10, and modified the dual rate setup so that FMODE0 is scaled to 60 with 20 expo and FMOD1 is 80 with 20 expo. Should make it fly a little smoother. Throttle trim is disabled, but pushing the throttle trim button up will toggle video camera on and off. One minor thing I have not isolated is that it sometimes comes on when you bind instead of being in the off state so keep your eye on that if you use the f…

WLToys V931 (V977 V2)

Anonymous (anonymous@undisclosed.example.com) — 2015-11-25T22:52:26-0700

WLToys V931 (V977 V2) Devo8s Has trims for 6G (when hovering in 6g mode, use trims as normal) 11CH CH1 = Thr CH2 = Ail CH3 = Ele CH4 = Rud CH5 = D/R > AIL DR0 = -100 > Low (Normal) .....................AIL DR1 = 100 > High CH6 = TH > RUD DR0 = -100 > Off

X Quadcopter/Crius Multiwii SE/Devo 10/1002 RX

Anonymous (anonymous@undisclosed.example.com) — 2013-03-20T19:24:57-0700

X Quadcopter/Crius Multiwii SE/Devo 10/1002 RX Attached is my new Setup for a X525 Quadcopter(should work for any X-Quad). Board is Crius Multiwii SE V2.1. Radio is Devo 10 with 1002RX D/R is 75%, Exp at 25% and 100%/Line for the Elev (Pitch) and Ail (Roll).

YD717 model

Anonymous (anonymous@undisclosed.example.com) — 2014-02-18T21:11:28-0700

YD717 model Fmode0: gentle Fmode1: good for indoor Fmode2: aggressive Sticky throttle cut on Rudder DR1. Auto-flip control is on the gear switch. YD717 LED red means auto-flip is enabled. model1