User Tools

Site Tools


Joomla says you aren't logged in
release_notes:5.0.0

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
release_notes:5.0.0 [2016/04/30 10:02]
PhracturedBlue
release_notes:5.0.0 [2017/05/17 08:03]
Texacate added the date 5.0.0 was released
Line 1: Line 1:
-===== Version 5.0.0 (Unreleased) ​===== +===== Version 5.0.0 ===== 
-** NOTE: Deviation ​5.0.0 has not been released ​yet.  There release notes are a work-in progress**+Version ​5.0.0 was released ​on 2016-04-30
  
-**IMPORTANT:​ You must install the filesystem along with the new firmware. ​ Make sure to save your models first!**+**IMPORTANT:​**\\ 
 +**You must install the filesystem along with the new firmware. ​ Make sure to save your models first!**\\ 
 +**The configuration of hardware mods has changed since the previous 4.0.1 version. Instead of the tx.ini, they are in a new hardware.ini file, just like they were in the last nightly builds.**
  
 ==== Installation ==== ==== Installation ====
-  * Follow the instructions in the [[ http://​www.deviationtx.com/​user-manual | User Manual ]] that applies to your transmitter+  * Follow the instructions in the [[ https://​www.deviationtx.com/​user-manual | User Manual ]] that applies to your transmitter
  
 ==== Critical bug fixes ==== ==== Critical bug fixes ====
Line 13: Line 15:
   * Allow reordering mixers on Devo7e/10   * Allow reordering mixers on Devo7e/10
   * Reworked telemetry to have different displays for different protocols   * Reworked telemetry to have different displays for different protocols
 +  * Add Range Test capability
 +  * Support permanent timers
   *    * 
-==== Minor Features ====+==== Minor Features ​/ Bug Fixes ====
   * Support hardware modification to add extra switches to the devo7e   * Support hardware modification to add extra switches to the devo7e
   * Support hardware modification to add vibration for Devo6/8   * Support hardware modification to add vibration for Devo6/8
Line 24: Line 28:
   * Fix power output contol for CC2500 protocols   * Fix power output contol for CC2500 protocols
   * Fix date displays   * Fix date displays
 +  * Support 4 alarm sounds for timers
 +  * Improve scrolling on many of the GUI screens
 +  * Support viewing virtual channels on Channel-test page
 +  * Telemetry alarms are more prominent
 +  * Properly display PPMIN on main page
 +  * Add debug log display option
 +  * Support newer Devo12S (with Rev2 Epson LCD driver)
 +  * Fix channel mapping when loading templates
 +  * Remove hardcoded fonts to improve theme-ability
   * Protocol fixes   * Protocol fixes
       * YD717 - Fix channels for rudder, aileron, elevator       * YD717 - Fix channels for rudder, aileron, elevator
Line 29: Line 42:
       * YD717 - Enable high-rate mode       * YD717 - Enable high-rate mode
       * YD717 - Support receiver throttle saftey       * YD717 - Support receiver throttle saftey
-      * YD717 - Don'​t ​hange the transmitter waiting ​fro a response from the model+      * YD717 - Don'​t ​hang the transmitter waiting ​for a response from the model
       * Properly handle Tx mode in Hubsan protocol       * Properly handle Tx mode in Hubsan protocol
       * DSM2/X - telemetry display fixes. ​ Support temperature display       * DSM2/X - telemetry display fixes. ​ Support temperature display
-      * Show dialog for WK* protocols ​until biding is complete +      * DSM2/X - support extended telemetry info 
-      * Support up to 12 channels ​on USBHID+      * DSM2/X - fix GPS heading units 
 +      * DSM2/X - RSSI in dBM 
 +      * WK* - Show dialog ​until biding is complete 
 +      * USBHID - Support up to 12 channels
       * V202 - Support bind on power-up       * V202 - Support bind on power-up
 +      * PPMOUT - Allow more than 10 channels
 +      * V202 - Add 250kbps mode, headless, and calibration
 +      * HiSky - Support 3/6 axis option
 +      * Devo - Fix loss of signal issue with telemetry enabled
 +      * Flysky - Update packet period to increase compatibilty with more receivers
  
 ==== New protocols ==== ==== New protocols ====
Line 45: Line 66:
       * HM380 protocol       * HM380 protocol
       * KN (V977) protocol       * KN (V977) protocol
 +      * ESky150 protocol
 +      * Bluefly HP100
 +      * Flysky supports WLToys V6x6, v919, v913 v915
 +      * CX10 protocol
 +      * CG023 protocol - supports EAchine CG023 / 3D X4 / Attop YD-829(C) ​
 +      * Joysway protocol
 +      * Hontai protocol
 +      * MT99 protocol - Supports Eachine H7
 +      * FY326 protocol
 +      * Bayang protocol - Supports H8 model and others
 +      * MJXq protocol
 +      * H8_3d protocol
 +      * Futaba S-FHSS protocol
release_notes/5.0.0.txt (22270 views) · Last modified: 2017/05/17 08:03 by Texacate