User Tools

Site Tools


Joomla says you aren't logged in
release_notes:5.0.0

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
release_notes:5.0.0 [2016/04/30 10:28]
PhracturedBlue
release_notes:5.0.0 [2017/01/23 00:43]
FDR https
Line 1: Line 1:
-===== Version 5.0.0 (Unreleased) ​===== +===== Version 5.0.0 ===== 
-** NOTEDeviation 5.0.0 has not been released yet.  There release notes are a work-in progress** +**IMPORTANT:**\\ 
- +**You must install the filesystem along with the new firmware. ​ Make sure to save your models first!**\\ 
-**IMPORTANT: ​You must install the filesystem along with the new firmware. ​ Make sure to save your models first!**+**The configuration of hardware mods has changed since the previous 4.0.1 version. Instead of the tx.ini, they are in a new hardware.ini file, just like they were in the last nightly builds.**
  
 ==== Installation ==== ==== Installation ====
-  * Follow the instructions in the [[ http://​www.deviationtx.com/​user-manual | User Manual ]] that applies to your transmitter+  * Follow the instructions in the [[ https://​www.deviationtx.com/​user-manual | User Manual ]] that applies to your transmitter
  
 ==== Critical bug fixes ==== ==== Critical bug fixes ====
Line 29: Line 29:
   * Improve scrolling on many of the GUI screens   * Improve scrolling on many of the GUI screens
   * Support viewing virtual channels on Channel-test page   * Support viewing virtual channels on Channel-test page
-  * Telemetry ​alars are moe prominent+  * Telemetry ​alarms ​are more prominent
   * Properly display PPMIN on main page   * Properly display PPMIN on main page
   * Add debug log display option   * Add debug log display option
 +  * Support newer Devo12S (with Rev2 Epson LCD driver)
 +  * Fix channel mapping when loading templates
 +  * Remove hardcoded fonts to improve theme-ability
   * Protocol fixes   * Protocol fixes
       * YD717 - Fix channels for rudder, aileron, elevator       * YD717 - Fix channels for rudder, aileron, elevator
Line 37: Line 40:
       * YD717 - Enable high-rate mode       * YD717 - Enable high-rate mode
       * YD717 - Support receiver throttle saftey       * YD717 - Support receiver throttle saftey
-      * YD717 - Don'​t ​hange the transmitter waiting ​fro a response from the model+      * YD717 - Don'​t ​hang the transmitter waiting ​for a response from the model
       * Properly handle Tx mode in Hubsan protocol       * Properly handle Tx mode in Hubsan protocol
       * DSM2/X - telemetry display fixes. ​ Support temperature display       * DSM2/X - telemetry display fixes. ​ Support temperature display
       * DSM2/X - support extended telemetry info       * DSM2/X - support extended telemetry info
       * DSM2/X - fix GPS heading units       * DSM2/X - fix GPS heading units
 +      * DSM2/X - RSSI in dBM
       * WK* - Show dialog until biding is complete       * WK* - Show dialog until biding is complete
       * USBHID - Support up to 12 channels       * USBHID - Support up to 12 channels
Line 49: Line 53:
       * HiSky - Support 3/6 axis option       * HiSky - Support 3/6 axis option
       * Devo - Fix loss of signal issue with telemetry enabled       * Devo - Fix loss of signal issue with telemetry enabled
 +      * Flysky - Update packet period to increase compatibilty with more receivers
  
 ==== New protocols ==== ==== New protocols ====
Line 64: Line 69:
       * CX10 protocol       * CX10 protocol
       * CG023 protocol - supports EAchine CG023 / 3D X4 / Attop YD-829(C) ​       * CG023 protocol - supports EAchine CG023 / 3D X4 / Attop YD-829(C) ​
 +      * Joysway protocol
 +      * Hontai protocol
 +      * MT99 protocol - Supports Eachine H7
 +      * FY326 protocol
 +      * Bayang protocol - Supports H8 model and others
 +      * MJXq protocol
 +      * H8_3d protocol
 +      * Futaba S-FHSS protocol
release_notes/5.0.0.txt (22927 views) · Last modified: 2017/05/17 08:03 by Texacate