Blade Nano CPX/mCPX/130X - 3 Difficulty Modes

I made this model based off my other Blade models.
It has 3 difficulty modes: Beginner, Standard, 3D. The difficulty modes are controlled with the Flight Mode Switch.

This model is for the Blade Nano CPX/mCPX BL.
There are models below this post for the Blade 130X and Blade mCPX V1/V2.


Normal - Beginner Settings

No negative pitch for normal mode so you don’t slam the heli down if you pull the stick down to fast. Zero degrees pitch at mid stick. Mild pitch.
D/R = 50% EXP +30%

ST-1 - Standard Settings

-3* negative pitch. Zero degrees pitch at mid stick. More aggressive pitch.
D/R = 70% EXP +30%

ST-2 - 3D Settings

Full +/- 3D pitch curve. Zero degrees pitch at mid stick. Aggressive pitch.
D/R = 125% EXP LIN



Model 49 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S.

* This model will not work for deviation firmware v2.1 or v3.

• Throttle hold on the RUDD D/R switch.
• 7 Point Throttle and Pitch Curves.
• TX Power=100mW
• Channels=7
• Protocol=DSMX
• No Fixed ID
• Stick Mode 2
If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Throttle Curve

Normal: Linear Curve

ST-1: V Shaped Throttle Curve

ST-2: 100% Flat Across


Throttle Hold is active on RUDD D/R switch



Pitch Curve

No negative pitch for normal mode so you don’t slam the heli down if you pull the stick down to fast. Zero degrees pitch at mid stick. Mild pitch.

ST-1: -3* negative pitch. Zero degrees pitch at mid stick. More aggressive pitch.

ST-2: Full +/- 3D pitch curve. Zero degrees pitch at mid stick. Aggressive pitch.




DR/EXPO

Adjust D/R and EXPO to your personal preference.

DR/EXPO is controlled with the Flight Mode Switch.



Normal: Beginner Settings

ELEV D/R = 50% EXP +30%

AILE D/R = 50% EXP +30%

RUDD D/R = 100% EXP LIN



ST-1: Standard Settings

ELEV D/R = 70% EXP +30%

AILE D/R = 70% EXP +30%

RUDD D/R = 100% EXP LIN




ST-2: 3D Settings

ELEV D/R = 125% EXP LIN

AILE D/R = 125% EXP LIN

RUDD D/R = 100% EXP LIN







Download the Configuration Settings File.

Right click the "model.ini " and select "Save Target As" or "Save Link As" depending if you are using IE or Firefox.

Install the configuration settings file into your models folder (See my How to video below).

This will over-right the current file so make sure that model slot doesn’t
have a model being used in it. If it does rename the configuration settings file
to another number that you have free.

Example: The file you downloaded is named model5 so change the “5" to another slot
number that you don’t have a model setup for. If you have model slot 6 open rename the file to model6





How to Import/Export Deviation Firmware Models








-

This model is for the Blade 130X.

Model 50 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S.

* This model will not work for deviation firmware v2.1 or v3.

This model is for the Blade mCPX V1/V2.

Model 51 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S.

* This model will not work for deviation firmware v2.1 or v3.

I only received my DEVO10 yesterday. Thank you for the files, i was able to bind my two mcpx/v1/v2 i have. I had tryed numerous times to bind them before, but i failed. Only after i downloaded these files i was able to bind. Only that i had to change DSMX to DSM2 to bind them.

I have also downloaded the file for the 130X, but i will bind it later. For the time beeing i want to "study" what you have written in the files and try to adjust the values to better much my two mcpxs. This look like a hard task for me, because i have never had a DEVO tx before.