DeviationWiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
===== Align T-Rex 150 DFC - 3 Difficulty Modes =====

I made this model based off my other Align T-Rex 150 DFC models.

It has 3 difficulty modes: Beginner, Standard, 3D. The difficulty modes are controlled with the Flight Mode Switch.

__Normal__ - Beginner Settings

No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast. Zero degrees pitch at mid stick. Mild pitch.

D/R = 50% EXP +30%

__ST-1__ - Standard Settings

-3* negative pitch. Zero degrees pitch at mid stick. More aggressive pitch.

D/R = 70% EXP +30%

__ST-2__ - 3D Settings

Full +/- 3D pitch curve. Zero degrees pitch at mid stick. Aggressive pitch.

D/R = 125% EXP LIN

Model 48 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S.

* This model will not work for deviation firmware v2.1 or v3.
  * Throttle hold on the RUDD D/R switch.  * 7 Point Throttle and Pitch Curves.  * TX Power=100mW  * Channels=7  * Protocol=DSMX  * No Fixed ID  * Stick Mode 2
If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.

Set your ESC Li-po Cell Count setting to "AUTO". Default setting is 2 CELL.

ESC Settings

Functions

6. Li-Po Cell Count - Make sure to set this to "Auto".

Do not use the "2S" setting. You will have an extreme power/headspeed loss using the default "2S" setting.

__Throttle Curve__

Normal: Linear Curve

ST-1: V Shaped Throttle Curve

ST-2: More aggressive V Shaped Throttle Curve

Throttle Hold is active on RUDD D/R switch

__Pitch Curve__

Normal: No negative pitch for normal mode so you dont slam the heli down if you pull the stick down to fast. Zero degrees pitch at mid stick. Mild pitch.

ST-1: -3* negative pitch. Zero degrees pitch at mid stick. More aggressive pitch.

ST-2: Full +/- 3D pitch curve. Zero degrees pitch at mid stick. Aggressive pitch.

__Gyro Gain__ - These are the values I used then converted them to the deviation values.

Mix Switch

Pos 0: 65%

Pos 1: 70%

Pos 2: 75%

__DR/EXPO__

Adjust D/R and EXPO to your personal preference.

DR/EXPO is controlled with the Flight Mode Switch.

Normal: Beginner Settings

ELEV D/R = 50% EXP +30%

AILE D/R = 50% EXP +30%

RUDD D/R = 100% EXP +15%

ST-1: Standard Settings

ELEV D/R = 70% EXP +30%

AILE D/R = 70% EXP +30%

RUDD D/R = 100% EXP +15%

ST-2: 3D Settings

ELEV D/R = 125% EXP LIN

AILE D/R = 125% EXP LIN

RUDD D/R = 100% EXP LIN

Download the Configuration Settings File.

Right click the "model.ini " and select "Save Target As" or "Save Link As" depending if you are using IE or Firefox.

Install the configuration settings file into your models folder (See my How to video below).

This will over-right the current file so make sure that model slot doesnt

have a model being used in it. If it does rename the configuration settings file

to another number that you have free.

Example: The file you downloaded is named model5 so change the 5" to another slot

number that you dont have a model setup for. If you have model slot 6 open rename the file to model6

How to Import/Export Deviation Firmware Models

http://youtu.be/aXkvtbCXzsk

-

[[ .:align_t-rex_150_dfc_-_3_difficulty_modes:model48_2014-04-30 ]]
DeviationWiki

User Tools

Site Tools

Page Tools
