Joomla says you aren't logged in
                release_notes:5.0.0
                Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
| release_notes:5.0.0 [2016/04/30 10:28] PhracturedBlue | release_notes:5.0.0 [2017/05/17 08:03] (current) Texacate added the date 5.0.0 was released | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===== Version 5.0.0 (Unreleased) ===== | + | ===== Version 5.0.0 ===== | 
| - | ** NOTE: Deviation 5.0.0 has not been released yet. There release notes are a work-in progress** | + | Version 5.0.0 was released on 2016-04-30 | 
| - | **IMPORTANT: You must install the filesystem along with the new firmware.  Make sure to save your models first!** | + | **IMPORTANT:**\\ | 
| + | **You must install the filesystem along with the new firmware.  Make sure to save your models first!**\\ | ||
| + | **The configuration of hardware mods has changed since the previous 4.0.1 version. Instead of the tx.ini, they are in a new hardware.ini file, just like they were in the last nightly builds.** | ||
| ==== Installation ==== | ==== Installation ==== | ||
| - | * Follow the instructions in the [[ http://www.deviationtx.com/user-manual | User Manual ]] that applies to your transmitter | + | * Follow the instructions in the [[ https://www.deviationtx.com/user-manual | User Manual ]] that applies to your transmitter | 
| ==== Critical bug fixes ==== | ==== Critical bug fixes ==== | ||
| Line 29: | Line 31: | ||
| * Improve scrolling on many of the GUI screens | * Improve scrolling on many of the GUI screens | ||
| * Support viewing virtual channels on Channel-test page | * Support viewing virtual channels on Channel-test page | ||
| - | * Telemetry alars are moe prominent | + | * Telemetry alarms are more prominent | 
| * Properly display PPMIN on main page | * Properly display PPMIN on main page | ||
| * Add debug log display option | * Add debug log display option | ||
| + | * Support newer Devo12S (with Rev2 Epson LCD driver) | ||
| + | * Fix channel mapping when loading templates | ||
| + | * Remove hardcoded fonts to improve theme-ability | ||
| * Protocol fixes | * Protocol fixes | ||
| * YD717 - Fix channels for rudder, aileron, elevator | * YD717 - Fix channels for rudder, aileron, elevator | ||
| Line 37: | Line 42: | ||
| * YD717 - Enable high-rate mode | * YD717 - Enable high-rate mode | ||
| * YD717 - Support receiver throttle saftey | * YD717 - Support receiver throttle saftey | ||
| - | * YD717 - Don't hange the transmitter waiting fro a response from the model | + | * YD717 - Don't hang the transmitter waiting for a response from the model | 
| * Properly handle Tx mode in Hubsan protocol | * Properly handle Tx mode in Hubsan protocol | ||
| * DSM2/X - telemetry display fixes.  Support temperature display | * DSM2/X - telemetry display fixes.  Support temperature display | ||
| * DSM2/X - support extended telemetry info | * DSM2/X - support extended telemetry info | ||
| * DSM2/X - fix GPS heading units | * DSM2/X - fix GPS heading units | ||
| + | * DSM2/X - RSSI in dBM | ||
| * WK* - Show dialog until biding is complete | * WK* - Show dialog until biding is complete | ||
| * USBHID - Support up to 12 channels | * USBHID - Support up to 12 channels | ||
| Line 49: | Line 55: | ||
| * HiSky - Support 3/6 axis option | * HiSky - Support 3/6 axis option | ||
| * Devo - Fix loss of signal issue with telemetry enabled | * Devo - Fix loss of signal issue with telemetry enabled | ||
| + | * Flysky - Update packet period to increase compatibilty with more receivers | ||
| ==== New protocols ==== | ==== New protocols ==== | ||
| Line 64: | Line 71: | ||
| * CX10 protocol | * CX10 protocol | ||
| * CG023 protocol - supports EAchine CG023 / 3D X4 / Attop YD-829(C)  | * CG023 protocol - supports EAchine CG023 / 3D X4 / Attop YD-829(C)  | ||
| + | * Joysway protocol | ||
| + | * Hontai protocol | ||
| + | * MT99 protocol - Supports Eachine H7 | ||
| + | * FY326 protocol | ||
| + | * Bayang protocol - Supports H8 model and others | ||
| + | * MJXq protocol | ||
| + | * H8_3d protocol | ||
| + | * Futaba S-FHSS protocol | ||
release_notes/5.0.0.1462037334.txt.gz (36152 views) · Last modified: 2016/04/30 10:28 by PhracturedBlue
                             
			




