- Posts: 1
- Forum
- Model Configs, Templates, Skins
- Model Configs
- Settings for Walkera V450D03 with RX2703H-D needed
Settings for Walkera V450D03 with RX2703H-D needed
- PKB
- Topic Author
- Offline
I never needed to ask anything here, cause all my needs were posted.
But this time i haven't found settings for the Walkera V450D03 (the plastic one) with RX2703H-D.
Anyone can help me with that? Can i use any alternatives?
Thanks and have a nice day
Peter (PKB)
Please Log in or Create an account to join the conversation.
- clearprop88
- Offline
- Posts: 94
Please Log in or Create an account to join the conversation.
- Hexperience
- Offline
- Posts: 588
I can post mine when i get to my pc but really it only takes a few minutes to do a model config...
There are 10 types of people in this world. Those that understand binary and those that don't.
Please Log in or Create an account to join the conversation.
- Fernbediener71
- Offline
- Posts: 20
Before using Fmode 1+2 check them, i don't use these settings at the moment. The heli can 3D but the pilot not so far
Please Log in or Create an account to join the conversation.
- hellboy
- Offline
- Posts: 8
Please Log in or Create an account to join the conversation.
- Hexperience
- Offline
- Posts: 588
There are 10 types of people in this world. Those that understand binary and those that don't.
Please Log in or Create an account to join the conversation.
- evo165
- Offline
- Posts: 13
Can you explain how do you use the Fmod 1 and fmod 2 differently?
The fmod 1 is using throttle of only 30% at mid stick.
The fmod 2 is using throttle of 90% atmid stick.
When switching between the fmod 1 and 2, will the heli jumping/dropping?
Hope to seek and learn more from you, sir.
Please Log in or Create an account to join the conversation.
- Hexperience
- Offline
- Posts: 588
To use F2 I would start in f0 and as the heli is getting up to speed but still at zero pitch, flip to f2. The heli esc will then pump the same power into the motor no matter what the pitch is. (At this point you might want to look into governor mode)
Long story short, I'm still not at the point where I fly in F2. I start in f0, then go to F1 so I can do some flips and rolls and a little bit of inverted. So if you're not at the 3D stage yet stick with f0 and f1.
--- EDIT ---
Please check the throttle in F1. I think you should find that it's not at 30%. It should be +25 which is 62.5%... If it's not adjust it.
Also, I never used the standard gui only the advanced gui.
There are 10 types of people in this world. Those that understand binary and those that don't.
Please Log in or Create an account to join the conversation.
- evo165
- Offline
- Posts: 13
My last question, people are always telling me when going idle up f1 or f2...
It will be better to use higher head speed value of +70 to +100 (Deviation value) at mid stick. This give more constant speed on the head rather than varying the motor speed & pitch together if mid stick throttle is set too low. True?
In fact, I am just learning to fly normal sport & scale flying... No 3D for me yet... People advice the above will give me longer flight time due to constant head speed... Is this true?
I have so much more to learn...
Please Log in or Create an account to join the conversation.
- Diaz
- Offline
- Keep flying!
- Posts: 11
Erik
Please Log in or Create an account to join the conversation.
- Diaz
- Offline
- Keep flying!
- Posts: 11
Erik
Please Log in or Create an account to join the conversation.
- FDR
- Offline
BTW you turn on the tx in USB mode (holding the ENT), and simply copy it to the models directory renamed to a valid modelXX.ini filename...
Please Log in or Create an account to join the conversation.
- Hexperience
- Offline
- Posts: 588
There are 10 types of people in this world. Those that understand binary and those that don't.
Please Log in or Create an account to join the conversation.
- CUZN_J
- Offline
- Posts: 1
Thanks for all the great info that has been posted on this heli.
Please Log in or Create an account to join the conversation.
- aimHigher
- Offline
- Posts: 5
Please Log in or Create an account to join the conversation.
- CWSMTB
- Offline
- Posts: 1
Thank you
Please Log in or Create an account to join the conversation.
- Forum
- Model Configs, Templates, Skins
- Model Configs
- Settings for Walkera V450D03 with RX2703H-D needed
- Home
- Forum
- Model Configs, Templates, Skins
- Model Configs
- Settings for Walkera V450D03 with RX2703H-D needed