Align T-Rex 150 DFC - 3D Settings

This model is for use with the Spektrum DSM2/DSMX Satellite Receiver.

• 7 Point Throttle and Pitch Curves
• Throttle hold on the RUDD D/R switch
• TX Power=100mW
• Channels=7
• Protocol=DSMX
• No Fixed ID
• Stick Mode 2
If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.


Model 22 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S.

* This model will not work for deviation firmware v2.1 or v3.

Model 22-2 has Zero Degree Pitch when throttle hold is on.
This will help minimize damage in a crash as the swash and blades will be at mid stick zero degrees pitch.
This will also help prevent a boom strike.
The swash does not move when TH is on.
If you want control of the swash in TH to help you land in a crash don’t use this model use Model 22 instead.


Set your ESC Li-po Cell Count setting to "AUTO". Default setting is 2 CELL.

ESC Settings

Functions

6. Li-Po Cell Count - Make sure to set this to "Auto".
Do not use the "2S" setting. You will have an extreme power/headspeed loss using the default "2S" setting.

Throttle Curve - These are the values I used then converted them to the deviation values and 7 point curves.

NORM - 0% 30% 50% 55% 60%
ST- 1 - 100% 90% 80% 90% 100%
ST- 2 - 100% 90% 80% 90% 100%


Throttle Hold is active on RUDD D/R switch



Pitch Curve

Normal: -3* negative pitch. Zero degrees pitch at mid stick.

ST-1: Full +/- 3D pitch curve. Zero degrees pitch at mid stick.

ST-2: Full +/- 3D pitch curve. Zero degrees pitch at mid stick.



Gyro Gain - These are the values I used then converted them to the deviation values.

Mix Switch

Pos 0: 65%

Pos 1: 70%

Pos 2: 75%



DR/EXPO

Adjust D/R and EXPO to your personal preference.


Switch Position

0- ELEV D/R = 100% EXP +30%

0- AILE D/R = 100% EXP +30%

RUDD D/R = 100% EXP -6%


Switch Position

1- ELEV D/R = 125% EXP LIN

1- AILE D/R = 125% EXP LIN

RUDD D/R = 100% EXP -6%











Download the Configuration Settings File.

Right click the "model.ini " and select "Save Target As" or "Save Link As" depending if you are using IE or Firefox.

Install the configuration settings file into your models folder (See my How to video below).

This will over-right the current file so make sure that model slot doesn’t
have a model being used in it. If it does rename the configuration settings file
to another number that you have free.

Example: The file you downloaded is named model5 so change the “5" to another slot
number that you don’t have a model setup for. If you have model slot 6 open rename the file to model6





How to Import/Export Deviation Firmware Models






-

Will this work on v3 with 7e or must the upgrade be performed first. Are there any tutorials to walk through the switching of output channels ?

I tried some v4 models in the v3 emulators (Devo 7e, 8, 10).
This model will not work for deviation firmware v2.1 or v3.
See this post for more information.
deviationtx.com/forum/model-configs/2578...er-settings?start=20

Model updated (4).

I just found out the Align manual was incorrect on the gyro values.


The model first posted gyro settings were:


Gyro Gain - These are the values I used then converted them to the deviation values.

Mix Switch

Pos 0: 55%

Pos 1: 65%

Pos 2: 75%



Updated model gyro settings are now:


Gyro Gain - These are the values I used then converted them to the deviation values.

Mix Switch

Pos 0: 65%

Pos 1: 70%

Pos 2: 75%


70% to 75% is the most common values used on the internet. Fine tune the gyro gain to meet your needs.

Tom: will this work with Devo7? I am currently using your standard model; but I would like to see if I can fly the 3d.

I think you mean Devo 7e as the Devo 7 is not supported by the Deviation firmware.

My models will bind and work with the Devo 7e.
My custom GUI in the model file is also made to use with the 7e.

The issue is that the 7e has less switches. So you will only have one stunt mode plus you will not have DR/EXPO 1 and 2.

See my post here for an example:


deviationtx.com/forum/model-configs/2686...tings?start=20#20940