Nine Eagles Solo Pro 180 3D - Standard Settings

More
01 Feb 2014 16:59 - 15 Feb 2014 23:38 #19600 by Tom Z
Nine Eagles Solo Pro 180 3D (318A)


This model was started by ave1 and I added the rest of the settings needed. ave1 test flew the model with good results.


  • Low dual rates and positive expo to tame the heli down
  • Throttle hold on the RUDD D/R switch
  • 7 Point Throttle and Pitch Curves
  • TX Power=100mW
  • Channels=7
  • Protocol=J6Pro
  • No Fixed ID
  • Stick Mode 2
  • If you need Stick Mode 1, 3, or 4 load the model into your transmitter then change the Stick Mode in the transmitter settings.




    Model 42 is for deviation firmware v4 and the DEVO 6/6S/8/8S/10/12/12S.

    * This model will not work for deviation firmware v2.1 or v3.



Gyro Gain - These are the values I used then converted them to the deviation values.


Gear Switch

Pos 0: 25%

Pos 1: 75%




Throttle Curve

Normal: Custom Curve

ST-1: V Shaped Throttle Curve

ST-2: V Shaped Throttle Curve

Throttle Hold is active on RUDD D/R switch




Pitch Curve

Normal: -3* negative pitch. Hover at about half throttle.

ST-1: Full +/- 3D pitch curve. Zero degrees pitch at mid stick.

ST-2: Full +/- 3D pitch curve. Zero degrees pitch at mid stick.





DR/EXPO

Adjust D/R and EXPO to your personal preference.


Switch Position


0- ELEV D/R = 70% EXP +30%

0- AILE D/R = 70% EXP +30%

RUDD D/R = 100% EXP LIN


Switch Position


Switch Position

1- ELEV D/R = 100% EXP +30%

1- AILE D/R = 100% EXP +30%

RUDD D/R = 100% EXP LIN







Download the Configuration Settings File.

Right click the "model.ini " and select "Save Target As" or "Save Link As" depending if you are using IE or Firefox.

Install the configuration settings file into your models folder (See my How to video below).

This will over-right the current file so make sure that model slot doesn’t
have a model being used in it. If it does rename the configuration settings file
to another number that you have free.

Example: The file you downloaded is named model5 so change the “5" to another slot
number that you don’t have a model setup for. If you have model slot 6 open rename the file to model6





How to Import/Export Deviation Firmware Models






-
Attachments:
Last edit: 15 Feb 2014 23:38 by Tom Z.

Please Log in or Create an account to join the conversation.

More
04 Feb 2014 06:00 #19818 by Tom Z
Replied by Tom Z on topic Solo Pro 180 - Standard Settings
Update:


I changed the 5 point throttle and pitch curves to 7 point throttle and pitch curves.
I removed the Gyro gain from the MIX switch. It had three gyro gain settings 25% - 50% - 75%. The 50% setting turned out to be adjustment mode (gyro gain off).
If you were to hit the MIX switch by mistake in flight to the 50% setting the helicopter would spin on you so I removed the 50% setting and assigned the Gyro gain to the Gear switch.


Gear Switch

Pos 0: 25%

Pos 1: 75%



Here is what the MIX settings were.


Gyro Gain

Mix Switch

Pos 0: 25%

Pos 1: 50%

Pos 2: 75%


All the values above were then converted to the deviation values.

Please Log in or Create an account to join the conversation.

Time to create page: 0.033 seconds
Powered by Kunena Forum