- Posts: 776
Which is the latest nightly with telemetry on/off?
- aMax
- Topic Author
- Offline
Less
More
14 Jul 2015 00:27 #35419
by aMax
Devo7e, TaranisQ X7, R9M , 4in1 MM, Futaba FC18plusV3.2 & DFT/FLD-02
Which is the latest nightly with telemetry on/off? was created by aMax
...for Devo AND Dsmx ? It only works for Devo ....
The emulator has the option but not the the code on the box....
I tested deviation-devo7e-v4.0.1-2b69768 and deviation-devo7e-v4.0.1-c3007aa.
The emulator has the option but not the the code on the box....
I tested deviation-devo7e-v4.0.1-2b69768 and deviation-devo7e-v4.0.1-c3007aa.
Devo7e, TaranisQ X7, R9M , 4in1 MM, Futaba FC18plusV3.2 & DFT/FLD-02
Please Log in or Create an account to join the conversation.
- aMax
- Topic Author
- Offline
Less
More
- Posts: 776
17 Jul 2015 22:06 - 17 Jul 2015 22:07 #35588
by aMax
Devo7e, TaranisQ X7, R9M , 4in1 MM, Futaba FC18plusV3.2 & DFT/FLD-02
Replied by aMax on topic Which is the latest nightly with telemetry on/off?
Thanks for your attention.
Just for your information, went back to Indigo's branch. Assuming the latest one is the best, I flashed deviation-devo7e-v4.0.1-103607a (05/10/2015).
But, there is a fault with Devo and telemetry on/off. My SuperCP (no telemetry) did not bind if I had chosen the off state.
As soon as I switch telemetry off, she is loosing bind and rebinds with telemetry on.
Not binding...??....at first I was thinking my rx board has gone bad.
Therefore I am back to deviation-devo7e-v4.0.1-db5dcb3 (03/30/2015), where this does not happen and which worked for me
even at 100mW and a RX615X till end of LOS.
Range is more important to me (fpv quad) than some values for glitches and loss which my clone rx don't support anyway.
I think, this was not intended and Indigo will have a look on this as soon as he gets time again.
Just for your information, went back to Indigo's branch. Assuming the latest one is the best, I flashed deviation-devo7e-v4.0.1-103607a (05/10/2015).
But, there is a fault with Devo and telemetry on/off. My SuperCP (no telemetry) did not bind if I had chosen the off state.
As soon as I switch telemetry off, she is loosing bind and rebinds with telemetry on.
Not binding...??....at first I was thinking my rx board has gone bad.
Therefore I am back to deviation-devo7e-v4.0.1-db5dcb3 (03/30/2015), where this does not happen and which worked for me
even at 100mW and a RX615X till end of LOS.
Range is more important to me (fpv quad) than some values for glitches and loss which my clone rx don't support anyway.
I think, this was not intended and Indigo will have a look on this as soon as he gets time again.
Devo7e, TaranisQ X7, R9M , 4in1 MM, Futaba FC18plusV3.2 & DFT/FLD-02
Last edit: 17 Jul 2015 22:07 by aMax.
Please Log in or Create an account to join the conversation.
Time to create page: 0.026 seconds
- Home
- Forum
- Development
- Protocol Development
- Which is the latest nightly with telemetry on/off?