Flysky AFHDS 2A, protocol as used i10, i6, iT4,

ok, good to know that it is not included at Ver. 1.3

Hello Alexandro,

my TGY-i10 supports the channel expander on iA6B AND iA10 RX - in TX menue RX setup you have to choose the menu ibus setup. So your are able to allocate. The differnce between TGY-i6 and TGY i10 TX is just, the i6 add channels to it´s menu, the i10 stays at 10 channels. So it do has the Servo-bus.

All of this is for the TGY-i10 FW 1.07 (not the FW 1.07 "freerider".

greetings
Andreas

For the iA6B also for the iA10 the TX shows only error rate in percent. (Menu RX setup -> range test -> hold trainer-switch.
So it´s different in the GUI of the TX´s.

The iA6 does nothing.

checked on TGY-i10 FW 1.07 (not the freerider of the 1.07).

By the way, perhaps it might be helpfull, at HK I posted some informations about the "Factory Mode" www.hobbyking.com/hobbyking/store/__5845...lemetry_Mode_2_.html

A N D - oh - a new firmware for the TGY-i10 is out - you will see on the same link. I will test...............Perhaps there are also updates for the RX´s in.

I´ll come back, when checked
........

Andreas

OKAY,

FW update TGY1.07 -> 1.08 is done. So I have to correct my last post. (Sorry).

Also as aspected - FW update for the iA10 RX, Information was displayed direct after binding TX/RX
Also update for the iA6B RX. (FW 1.4 to FW 1.8 - for both)

TGY-i10 now shows RSSI . It´s displayed for RX iA10 and RX iA6. Also new - RSSI is displayed in the main screen.
When choosing [RX-setup] -> [display sensors], the signal strength (10 highes), RSSI -60 dBm, Noise -108 dBm and SNR 48 dB is displayed...

Now it has an new menue for s.bus - can´t test this - sorry no equipment for this.

Also a new menu "sprectrum analyser" - nice.

old menu "i-setup" is gone - I guess this was any test for s.bus menu

RX iR4 is still not supported - AFHDS 2 - that´s the same as goebish explained.

Sorry for talking about "old" FW 1.07 in my las post of the TGY i10 - update was from 19.05.2016....

Greetings

I received my IA6B receiver anything that needs to be tested with devo 7e?
Whats the latest build, as I like to keep also Frsky X protocol.

Hi Goebish, I tested your release as posted above with my devo 7e

I binds and works! Seems to very quickly lock!
I tested FS-IA6B, to bind you must power it with bindplug in B/Vcc port, powering on with the receiver switch pushed doesn't work.
Servo in the channels works!

Then I tested I-bus output , using Raceflight / Betaflight, the CLI command is:
set serialrx_provider = IBUS
save
All 8 channels are working. (I can test more there seem to be max 14 channels possible with ibus)

then about scale, -100 +100 (default) result in 1000 - 2000, is defaults for Raceflight Betaflight.
when setting Scale -125 +125 result in 900 - 2100, is the max as higher and signal will overflow.

Telemetry, I only see the Rx =voltage in my case 4.78V it seems stable and reliable.
I do not see RSSI, or signal quality


Could you explain about the settings;
PPM ON/OFF? Does it mean you can switch port 1 on Rx, to output ppm, or channel 1? (PPM not tested by me yet)
I tried it but when set ppm on, a standard servo still works in channel 1, so not sure...

Servo Hz, default 50. Is it the over the air transmission of updates? So should I set to 400hz? Or is it Rx output rate
to Servo? When set to 400Hz reboot 7e, at least can confirm servo and I bus still works like when set to 50Hz.

RXID1 What does it mean
RXID2 what does it mean
No Failsave Feature

I will also mod my RX, that instead of Regulated Rx voltage you can monitor 1 external voltage, the quad flight pack and generate alarm for empty pack. Described here:
www.rcgroups.com/forums/showpost.php?p=33432940&postcount=23


Ohh one more thing; the firmware above as tested 7e 5.0.0 b0020095, there is some bugs in the menus and I sometimes can't escape/exit menu's.
I then need to restart my 7e to get away from the menu.

Ah, I just edited my post....

goebish wrote:
That's normal, you have to update the iA6B to firmware 1.6 to get RSSI in dB, but I'll add signal quality (error rate).

Hi Goebish,
Where can I find some info. about iA6B firmware update,would you give me a link?
Thanks a lot.

@ dc59

The firmware for the iA6B comes within the FW for the i10 TX. So first download this and update the TX.

After this the iA6B receiver update (for Turnigy i10 actually V 1. will be done by the TGY-i10 TX. Take care for the different firmwares for different resellers - this is for the Turnigy i10.
You don´t have to push the button [update] on the receiver (next to LED for iA6B or for iA10 the button on the buttom side).

- receiver has to be already binded to the TX.
- Choose menu [RX Setup]
- scroll down to last menu [Update receiver]
- press [Yes]
- See what happens . The TX is displaying the last and the new FW version - or, if the there is no newer RX FW, it will display "FW is already the newest....or so...".

Further I tried to find out the RX-ID by using the i10 GUI, as by using the Factory Mode.
Can´t find any menu in user GUI. So switched to the Factory Mode.
www.hobbyking.com/hobbyking/store/upload...8233211X433170X2.pdf

There you will find in menu [Production Information] - [Radio Information] the option to display the TX and RX ID - BUT: for all receivers (iA6, iA6B and also for iA10) the RX ID is all the time "0" - whatever this is telling us???

Success.

Goebish full credits for your work, thanks man !!
First results look very promising !


I do not own any i10, but it sounds pretty "state of the art" to update receiver over the air !
If there is no other means to flash the Rx from a pc, hmmmm.......

@Evil Pusher
Thank you so much!
But I have only i6 TX, I don't have an i10 , that's too bad!
I checked my i6 RX menu, there is no [Update receiver] item.

Wondering how that works, Tx sends command to Rx > Rx to go to flash mode, than Rx it waits for file being transferred from Tx to Rx, when transfer ready it flashes the Rx?

As mentioned PPM on/off from devo 7e, in my case cppm on channel 1 of the Rx, I still be able to control standard servo, so I doubt cppm enabling works.

@dc59 - did you tried the [update] button on the receivers itself? Perhaps this my start an RX update....

@ goebish - yes, the iA10 is based on the stm32.......

www.dropbox.com/sh/6is2ozp4vgxhthw/AAC24...xzs32qxkNqYqzsa?dl=0 Pic inside

woa , super coder .
firmware RX i10 ?

@ goebish,
yes, the iA6B has an STM32.......

You will have an iA10 and an iA6B within the next days (DHL - Tracking comes tomorrow by PM). So, you may do with it whatever you like.

I have an ST-Link V2 STM8 STM32 USB Programmer 3,3V 5V SWD 212

---

---

---

---

---

just ordered.