- Posts: 9
Cheerson CX10A has new another board.
- song1116
- Topic Author
- Offline
A couple of days ago I bought CX10A and I tried to bind it using IR8M.
I have tried CX10 -> Green and Blue also.
However I couldn't bind it.
So I have torn down CX10A and Transmitter.
Can you please take a look pictures below?
Is it possible to bind this CX10A using IR8M?
If possible, what protocol should I set?
Thanks for helping me..
Please Log in or Create an account to join the conversation.
- song1116
- Topic Author
- Offline
- Posts: 9
Is there any idea?
Please Log in or Create an account to join the conversation.
- goebish
- Offline
- I Void Warranties
- Posts: 2631
I think it's using a XNS1042 MCU with builtin xn297l transceiver (SOIC-16, antenna connected to IC pin #1 in the transmitter), there's a chance it can be reverse engineered and added to Deviation but it can't be done with a logic analyzer, someone would have to send one to a developer for analysis.
Please Log in or Create an account to join the conversation.
- song1116
- Topic Author
- Offline
- Posts: 9
To verify if the recent CX10 and CX10A have used same protocol, I placed an order of CX10 from Banggood.
It will take a time.. after receiving, I will report it here..
BTW If I want to send sample,should I send sample to who and where?
Is there any developer to help this issue?
Please Log in or Create an account to join the conversation.
- goebish
- Offline
- I Void Warranties
- Posts: 2631
Note that I believe the TX is using a XNS1042 (and Cheerson has always used nrf24l01 compatible transceivers so far) but I can't be sure, so there's no guaranty.
Please Log in or Create an account to join the conversation.
- song1116
- Topic Author
- Offline
- Posts: 9
Anyway. let me check first if the recent CX10 and CX10a have same transmitter and receiver..
And then I would like to ask you if you don't mind..
Thanks a lot for helping us.. =)
Please Log in or Create an account to join the conversation.
- goebish
- Offline
- I Void Warranties
- Posts: 2631
If you PM me please post here as well because email notification doesn't work for PMs and I don't always check.
Please Log in or Create an account to join the conversation.
- song1116
- Topic Author
- Offline
- Posts: 9
Please Log in or Create an account to join the conversation.
- Moeder
- Offline
- Posts: 796
Please Log in or Create an account to join the conversation.
- song1116
- Topic Author
- Offline
- Posts: 9
Anyway what I should do? please let me know.
I will follow up and send it back to you. Thanks..
FYI, my transmitter is iRangeX iRX-IR8M.
Please Log in or Create an account to join the conversation.
- goebish
- Offline
- I Void Warranties
- Posts: 2631
Here is a test build that includes the new XN297 Dump feature.
First we'll check if this transmitter is using a XN297 compatible transceiver.
Download and flash this build to your IR8M:
www.dropbox.com/sh/857qdhte2dwmdmy/AAC0e...zL6VTrp0f1x9EJa?dl=0
On your transmitter, go to model menu / model setup then select a blank model and set it to "XN297 Dump" protocol.
Go to the Transmitter menu then XN297 Dump
Turn on scan by setting mode to 1 Mbps (Off -> 1 Mbps) then highlight < Ch 0 > and press ENT to start scanning.
Turn on your CX10A transmitter.
If valid packets are detected it should show "Valid CRC found!" on the bottom on the screen.
If nothing is found, try 250 K mode instead of 1 Mbps.
example with a Bayang transmitter:
Please Log in or Create an account to join the conversation.
- Moeder
- Offline
- Posts: 796
Please Log in or Create an account to join the conversation.
- song1116
- Topic Author
- Offline
- Posts: 9
Thanks..
Please Log in or Create an account to join the conversation.
- song1116
- Topic Author
- Offline
- Posts: 9
I am sorry for bad news.
This firmware didn't detect any valid packet. it did continuous scaning..
Please take a look attached pictures.
If there is anything that I can do, please let me know.. I will do with my pleasure.
Thanks..
Best Regards,
Keith
Please Log in or Create an account to join the conversation.
- goebish
- Offline
- I Void Warranties
- Posts: 2631
That might be a HS6200 but a SDR device is required to check that.
Please Log in or Create an account to join the conversation.
- song1116
- Topic Author
- Offline
- Posts: 9
Please Log in or Create an account to join the conversation.
- pzcato
- Offline
- Posts: 6
I have 4 of these little quads, it would be great to see deviated.
Please Log in or Create an account to join the conversation.
- goebish
- Offline
- I Void Warranties
- Posts: 2631
Please Log in or Create an account to join the conversation.
- pzcato
- Offline
- Posts: 6
Where can I find your contact details?
PS. Thanks for doing stuff life this, your protocol developments have inspired so many people (young and old!) to get into this stuff. Amazing, inspiring stuff!
Please Log in or Create an account to join the conversation.
- goebish
- Offline
- I Void Warranties
- Posts: 2631
Please Log in or Create an account to join the conversation.
- Home
- Forum
- Development
- Protocol Development
- Cheerson CX10A has new another board.