Joomla says you aren't logged in
model_config:walkera_master_cp_non_-_3d_model_devo_10:model2_2013-03-24
name=Master CP ADV mixermode=Advanced [radio] protocol=DEVO num_channels=8 tx_power=30mW [protocol_opts] Telemetry=On [channel1] template=simple [mixer] src=ELE dest=Ch1 [channel2] template=simple [mixer] src=AIL dest=Ch2 [channel3] template=complex [mixer] src=THR dest=Ch3 [mixer] src=THR dest=Ch3 switch=FMODE1 usetrim=0 [mixer] src=THR dest=Ch3 switch=FMODE2 usetrim=0 [mixer] src=THR dest=Ch3 switch=RUD DR1 scalar=-100 usetrim=0 curvetype=fixed [channel4] template=simple [mixer] src=RUD dest=Ch4 [channel6] template=complex [mixer] src=THR dest=Ch6 switch=FMODE0 scalar=70 usetrim=0 curvetype=7point points=0,0,0,0,33,66,100 [mixer] src=THR dest=Ch6 switch=FMODE1 scalar=70 usetrim=0 curvetype=7point points=-25,-16,-8,0,33,66,100 [mixer] src=THR dest=Ch6 switch=FMODE2 scalar=70 usetrim=0 curvetype=7point points=-35,-25,-14,0,33,66,100 [mixer] src=THR dest=Ch6 switch=RUD DR1 scalar=0 usetrim=0 curvetype=fixed [channel7] template=expo_dr [mixer] src=MIX0 dest=Ch7 scalar=82 curvetype=fixed [mixer] src=MIX0 dest=Ch7 switch=MIX1 scalar=75 curvetype=fixed [mixer] src=MIX0 dest=Ch7 switch=MIX2 scalar=0 curvetype=fixed [virtchan1] template=expo_dr [mixer] src=AIL DR0 dest=Virt1 curvetype=expo points=40,40 [mixer] src=AIL DR0 dest=Virt1 switch=AIL DR1 curvetype=expo points=30,30 [virtchan2] template=expo_dr [mixer] src=ELE DR0 dest=Virt2 curvetype=expo points=40,40 [mixer] src=ELE DR0 dest=Virt2 switch=ELE DR1 curvetype=expo points=30,30 [virtchan3] template=complex [mixer] src=THR dest=Virt3 switch=FMODE0 scalar=70 usetrim=0 curvetype=7point points=0,0,0,0,20,42,65 [mixer] src=THR dest=Virt3 switch=FMODE1 usetrim=0 curvetype=7point points=-35,-23,-12,0,33,66,100 [mixer] src=THR dest=Virt3 switch=FMODE2 usetrim=0 curvetype=7point points=-35,-23,-11,0,33,66,100 [mixer] src=THR dest=Virt3 switch=RUD DR1 scalar=0 usetrim=0 curvetype=fixed [trim1] src=LEFT_V pos=TRIMLV+ neg=TRIMLV- [trim2] src=RIGHT_V pos=TRIMRV+ neg=TRIMRV- [trim3] src=LEFT_H pos=TRIMLH+ neg=TRIMLH- [trim4] src=RIGHT_H pos=TRIMRH+ neg=TRIMRH- [timer1] src=THR [safety] Auto=min [gui-qvga] trim=4in barsize=half box1=Ch3 box2=Ch6 box3=Timer1 bar1=Ch1 bar2=Ch2 bar3=Ch3 bar4=Ch4 toggle1=ELE DR tglico1=0,1,0 toggle2=AIL DR tglico2=0,0,0 toggle3=RUD DR tglico3=0,2,0 toggle4=GEAR tglico4=0,4,0 quickpage1=Telemetry monitor
model_config/walkera_master_cp_non_-_3d_model_devo_10/model2_2013-03-24.txt (46958 views) · Last modified: 2013/03/24 08:42 by gapi
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
