Advanced Search

Starts up fine and initialises then screen goes blue. All the menu's are accessible and settings made in them work to the receiver. Nothing appears amiss except this blank screen. Any thoughts would be welcome. Cheers Peter

The problem is caused by JTAG not completely disabled which was originated in early 2019 during major code restructure. It's quite strange nobody reported this problem for so many years. Maybe most have moved onto other transmitters. Anyway, I've created a pull request for the fix.

Just returned to the hobby after a few years break. Upgraded my Ultimate 7e to the latest build from Hexfet "deviation-devo7e-256-v5.0.0-408f8c0". Got the error message "Missing Modules: MultiMod" right after upgrade. Has the hardware.ini file format changed? I'm using the original multimodule by PB. Appreciate for any suggestions. Here is the modules section of hardware.ini file I'm using:

[EDIT]
Installed the official nightly build on 2021-06-06 "deviation-devo7e-256-v5.0.0-c84450e", same problem. Tried the official release "deviation-devo7e-v5.0.0" and it works fine.

Hi,

Other similar models can work too.
This is a model config I made from scratch so may be someone could do it better. Anyway it works for me.
Using the Devo 8s, don't know if it can work on other transmitters. You can change the flight stabilization using the FMOD switch (0=Beginner, 1=Middle, 2=Expert).

I also edit an icon for the BF-109 plane.

I answer myself: Yes, latest builds already support it.

I read with interest the several posts regarding rx. However I am not clear on the answers given. So.....which of the two rx (701 and 704) are ppm. I am slow on catching up buy will fit one of these rx to my F450 Quad. Would like to use serial but have Naza M Lite FC which doesnt do serial. never mind. I appreciate if you can help me.
Peter

Hi , I need a little help here .
I just bought a bladeinductrix and I'm trying to bind it with my Devo f7 but it won't bind.
Thankyou.

Thank you for the explanations!
I will try first with the 2 antennas, I must have first a good working with the XK K110s!

Basically I would not use such an antenna cable, because there is an important and fixed matching between the transmitter module and the antenna, to which the cable must also fit. A mismatch could destroy the module in the worst case. This also happens, for example, if you operate the transmitter without an antenna. Whether there is a suitable cable for this I do not know.

I would recommend you to think about a 4in1 module, here all protocols are integrated and you can continue to use the original antenna. 4in1 modules are still available at AliExpress.

I don't think my 3in1 manage DEVO protocol! fr.aliexpress.com/item/1005002217994819....gatewayAdapt=glo2fra

Isn't the Devo protocol also provided by the 3in1 module you want to install?

If I want to keep the Devo module, is it unrealistic to use a twin cable like this?

Here is an example picture of a 3in1 module. On the top right of the module you see the antenna connector, which is clipped into the socket.
www.deviationtx.com/wiki/modulelist/3-in-1_module

The antenna cable is removed from the original RF module and the module is then removed from the devo. For this, the 3in1 module is installed and there the antenna cable is clipped in.

There is only one antenna cable that is led from the 3in1 module to the antenna.

Thank you!
I have not notifications for the replies, so I didn' t see it immediately!
I will look at that, I wonder how to wire the genuine and the 3in1 module on the same antenna!

The original antenna works fine with the multiprotocol module. I converted my Devo 12s years ago. The different protocols do not change the frequency of 2.4 GHz, so it fits.

All the answers to installing the module can be found here:
www.deviationtx.com/forum/7-development/...installation?start=0

Hi
I' m new with deviation!
I wonder if the genuine antenna from my devo10 could be wired with a 3in1 module, if yes, how? Only one antenna for the different protocols (that are not used at the same time I think!) could be more practical, but is there a risk?
Thank you!

Are you still alive?

Hi again! I want to add this protocol to transmitter github.com/DeviationTX/deviation/pull/1007/files
But build is little too huge what and how i can delete and still succesfully compile?

Hi i newbie in buisnes, few days ago i bought t8sg v2 with implemented omphobby protocol. I didnt know that is uncommon and updated deviationtx now im stuck with toy what i cant fly. Can somebody implement this for me or teach me how? github.com/DeviationTX/deviation/pull/1007/files
Sorry for my bad english

Matthewdupreez wrote: hey guys i have a Jumper T8sg plus that recently started showing me the USB icon on the screen, running deviation tx,
now i cannot seem to get my laptop to load the correct driver for me to either reflash the firmware. when the tx is in DFU mode, or to open and replace the files when it's in usb mode.
does anyone perhaps have the link for it? i'm running windows 10.
please help this is rather urgent.

Regards Matthew

PROBLEM SOLVED.

what any instructions forget to tell you is that there is a procedure to get it to work properly while bricked in usb mode.


it is as follows

turn off tx
plug tx into pc
turn on tx
vooila pc opens it's folders and allows me to format it and replace folders...


it does not work if it is turned on before plugged in...
sounds stupid. but if you don't think about it.... yea you pull your hair out