Dynam 7ch rx binds to 2602tx

Tell me where to obtain one of these Rx, and I'll try it out.

For example at nitroplanes:
www.nitroplanes.com/dy26chre.html

Dynam:


Walkera RX-2701:


Colored differently, but otherwise they are the same...

They both not compatible with 2801 protocol.

Well, I'll get one to add to my collection. Stil haven't figured out why 2601 protocol doesn't work though. It'll likely need to wait until I can actually experiment in person.

NotFastEnuf wrote: So 2801 protocol will not link to the 7 ch Rx? What about 2601 protocol? Is it not working at all? What can I do with my 2602 tx to help you?

Unless you have a logic analyzer, nothing at all.
Deviation will likely bind to the 7ch Rx, and some channels may work, but servos won't behave properly from my understanding.

You'll need to be able to sample an SPI bus (4 channels) at 8MHz which I think rules out parallel-port solutions.

I love my Saleae Logic, and would strongly recommend it. They also give great customer service.
But on a budget, you might look here for similar models:
sigrok.org/wiki/Fx2lafw

I personally like the unlimited sample-size supported by theses 'streaming' type analyzers, but at least one other user had good luck with one of these:
www.seeedstudio.com/depot/preorder-open-...-p-612.html?cPath=75
and even less expensive, this would likely also work:
www.seeedstudio.com/depot/logic-shrimp-v...p-803.html?cPath=174
or even:
www.seeedstudio.com/depot/bus-pirate-v3-...609.html?cPath=61_68

(regardless of choice, make sure you also get probe cables!)

With all that said, you can likely also choose to be patient. I won't be able to do much debug for another week anyway, and there are members with the necessary hardware to provide additional logs should they be necessary.

PhracturedBlue wrote: Well, I'll get one to add to my collection. Stil haven't figured out why 2601 protocol doesn't work though. It'll likely need to wait until I can actually experiment in person.

Because there is something is missing from both the documentation and implementation:
Ch1-4 are there, but only one bit is sent from Ch5 and Ch6 (which should be the pitch otherwise).
In the data package byte 5, 6, 7 are always null, however I think there should be something sent...

That is because all of the logs I've seen show those bytes zeroed out. It doesn't mean they aren't used, but does mean they weren't used in the configurations I have captures of.
One possibility is that these are treated just like the lower 4 channels. It would be easy to wire them up and see what happens I suppose.

Ch7 used for gyro sensitivity adjustment. By rotating V1 knob.

so 3 zeroed bytes, 3 missing channels, seems like a safe bet this is where they are.
Included is a trial DFU that adds 7 channel support to the WK2601 protocol. It is completely untested and may not work at all, but I'd be interested in feedback with any 2601-only Receivers.

Note. you need the filesystem (not dfu) from here:
www.deviationtx.com/forum/5-news-announc...l-build-fab82a525bdb

What filesystem to use? From v1.1.2 or ???

Good point. You need the new filesystem (not dfu) from here:
www.deviationtx.com/forum/5-news-announc...l-build-fab82a525bdb

I did not release an emulator that is compatible with that filesystem I think.
you can ask around, several folks have used the latest code with the new filesystem. It has some known issues (boot-loop on USB and telemetry page when exiting for instance) but overall is generally ok. Or you can wait another week when I am able to do proper testing myself.

The worst case is you need to go back to the official release.