Flysky AFHDS 2A, protocol as used i10, i6, iT4,

yes, after upgrade the tgy tx to 1.0.8 and and upgrading rx telemetry was lost.
after the restore to 1.0.? (was the file from you dropbox and also downgrade tx to 1.0.7 is working.
later on i will test it with devo 12

don't think so, i guess iti is a bug....
the tx can be downgradevia the gui on the tx, but not the rx.
anyhow, it workts for me.
can i support the further devolepment for the telemety with external sensors?
i have some voltage, rpm(optic) and iirc one temp sensor with i10 plugs workless in my box.
if this will help, pm me you adress.
btw. greart firmware.

king regards
jo

yes, i can do this.
reg
jo

Just to make sure before I order a FS-ia6B :

Will I be able to add this protocol in my devo 7E (non ultimate)?
I have A7105 installed and tested.
Thanks.

Great !
And I have an ST-Link if needed.
Thanks a lot for the amazing job btw.

Hi guys, first post!

First of all I'd like to thank all the developers of deviationtx and its protocols - you have given me hours of fun flying quads. Being an engineer myself I can really appreciate the complexity of the work you guys have put in. Keep up the good work, it is appreciated!

I've tried Devo 7E build posted a few pages ago and it works great in pwm mode with my recently bought unmodified Flysky FS-iA6B. I'd like to use ppm to free up a uart port on my flip32 running the newest cleanflight.

Is this possible with the current state of the deviation software? I've tried connecting CH1 from the receiver to CH1 on the Flip32 and set cleanflight to PPM. I also tried different settings in the /Model setup/PPM In/ menu on the Devo 7E. Changing that setting sometimes prevents me from getting back to the "main view". Is this a bug or - probably more likely - user error?

I guess the main question is: Is what I'm trying to do possible?

Thanks for the quick reply! I'll continue trying. Must have made a mistake somewhere along the way.

Just curious, is there any difference between this AFHDS 2A and the old AFHDS? Like in reliability/strenght/whatever?

Also what exactly makes this system "telemetry aware", is this dependent on the dual antenna system or is a dual antenna system used only to get the best signal via diversity?

Hello goebish!

Trying to bind an Eachine iA6 (rebranded FlySky, 6 channel park flyer PWM RX) to a 7e with A7105 module and your latest build - no joy.
LED on the RX (in bind mode) goes from fast blinking to slow blinking and stays slowly blinking with bind plug removed. Tried channel count from 6 to 12 (max on 7e).

Are there any chances to make it work or am I lost with this RX and it only works on the iA6B?

goebish wrote: I could buy one of those RX as I still have Alexandro's TGY-i10 TX but I don't think it would bind to a FlySky RX so that wouldn't help.

it should work, i talked to some guys on a meeting, the most off are flying flysky; i6 and i10 also both protocols.
reg
jo

it is 2. hand info,
the guys told me they are using al kinds off rx(tgy bangood,flysky), binding mostly to a TGY i10 running 1.07
alexandro told me simular; he bind a old 3 ch. flykky car rx to i10.
so i'm 90% shure it works

Hello everyone.
I check the operation of the receiver to have.

FS-A6
FS-IA4B
FS-IA6
FS-IA6B
FS-IA10

Operating in all of the above.
Great job.

I am glad when the 'S.BUS' also become possible, if possible.